Evolve SHOWROOMS Скачать руководство пользователя страница 49

Страница: 49 / 58

EVOLVE

evolvefurnituregroup.com • Page

Double Wall Overhead Glazed Door

Identify both left and right gables and determine their location on panel

STEP 1: Insert hooks of metal brackets into panel slot and pull gable down-
ward and tap with rubber mallet to ensure connection.

STEP 2: Push bottom bracket up and tighten cap nut to secure gable.

Bottom and Middle Shelf

STEP 3: Install PVC lip on bottom shelf by putting iton shelf lip and pushing
upward and forward shelf until it snaps on.

STEP 4: loosen cap nuts, position bottom shelf between gables, drop shelf
front on front studs, slide shelf forward.

STEP 5: Drop back of shelf on back studs, tighten the cap nuts.

Top Shelf

STEP 6: Loosen cap nuts, position top shelf between gables, drop shelf
back on back studs, slide shelf backward.

STEP 7: Drop front of shelf on front studs, tighten the cap nuts.

To install Glazed Sliding Door

STEP 8: Loosen front cap nuts of top shelf

STEP 9: Put Glass in upper tracks, lift top shelf front and put Glass in bot-
tom tracks, slide glass to middle and tighten cap nuts of top shelf.

To install Metal Handle

STEP 10: Take rubber and peel of protective paper, place rubber on glass

STEP 11: Slide Metal Handle on rubber.

INSTALLATION GUIDELINES

Содержание SHOWROOMS



























































Результаты поиска

Содержание SHOWROOMS

Отзывы:

Бренды по названию

Популярные бренды

Evolve SHOWROOMS, Руководство по установке

Результаты поиска

Содержание SHOWROOMS

Отзывы:

Бренды по названию

Популярные бренды