Evolve SHOWROOMS Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 58

background image

EVOLVE

evolvefurnituregroup.com • Page

23

INSTALLATION GUIDELINES

Sliding Panel Door Lock

If the floor is carpeted, ensure that carpet grippers (included in
hardware packet) are installed on the levelers of the panels, mainly
in door / opening. For permanent positioning, Floor Mount Plate is
recommended.

STEP 1: Locate and install the left or right bracket with faceplate.

STEP 2: Secure with supplied screws (1-1/2” for fabric module or
3/4 for aluminum frame).

STEP 3: Secure lock cam in open position. (Usae wire or a paper
clip).

STEP 4: Close the door and insert lock cam (Plunger) into the face
plate.

STEP 5: Keep lock assembly and door tight together. Request help
to accurately trace points by marker on the door. Mark the location
of the pilot holes they must be on the inside, of the workstation
side, of the acrylic screen.

The lock bracket assembly must be flush with the door acrylic side.

STEP 6: First drill the upper pilot hole. Do not push on the drill.
While drilling, be careful not to force any aluminum shavings into
the interior of the plastic flutes, as they may become visible.

STEP 7: Secure supplied screws (#8 1/2”) to lock assembly and
door.

Test the lock function.

STEP 8: If the location is correct, drill the second hole and secure
with the supplied screw.

STEP 9: Apply plastic lock assembly cover.

Floor Mount
Plate

1

2

3

4

5

7

«
...
21
22
23
24
25
...
»

Содержание SHOWROOMS



























































Отзывы:

Нет отзывов

Похожие инструкции для SHOWROOMS

Бренд: Navman Страницы: 17

Бренд: DAKO Страницы: 25

Бренд: 3M ESPE Страницы: 50

Бренд: VACGEN Страницы: 13

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: Idex Страницы: 141

Бренд: IDEAL Networks Страницы: 8

Бренд: IDEAL Networks Страницы: 5

Бренд: Radial Engineering Страницы: 16

Бренд: R&S Страницы: 61

Бренд: Rath Страницы: 5

Бренд: Wacker Neuson Страницы: 34

Бренд: ACS Страницы: 28

Бренд: Garrick Страницы: 8

Бренд: Emos Страницы: 8

Бренд: Emos Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды