manualshive.com logo in svg

Evolve SHOWROOMS, Руководство по установке

Поделиться
Скачать
Evolve SHOWROOMS Скачать руководство пользователя страница 48

EVOLVE

Page 

48 • 

evolvefurnituregroup.com

Double Wall Overhead

Identify both left and right gables and determine their location 

on panel

STEP 1: Insert  hooks of metal brackets into panel slot and pull 
gable downward and tap with rubber mallet to ensure connection

STEP 2: Push bottom bracket up and tighten cap nut  to secure 
gable

Bottom and middle shelf

STEP 3: Install PVC lip on bottom and middle shelf by putting it on 
shelf bottom and pushing upward and toward shelf until it snaps 
on 

Bottom and middle shelf

STEP 4: Loosen cap nuts, position  bottom shelf between gables, 
drop shelf front on front studs, slide shelf forward

STEP 5: Drop back of shelf on back studs, tighten the cap nuts
Top shelf

STEP 6: Loosen cap nuts, position  top shelf between gables, drop 
shelf back on back studs, slide shelf backward

STEP 7: Drop front of shelf on front studs, tighten the cap nuts.

 

STEP 8: Place door on top of overhead and center it between 
gables, secure hinges with provided screws without tightening 
screws

STEP 9: Close door and check that gaps are equal on both sides. 
If required, adjust door position by loosening screws and center 
door between  gables  then tighten screws

INSTALLATION GUIDELINES

Содержание SHOWROOMS



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды