manualshive.com logo in svg

Evolve SHOWROOMS, Руководство по установке

Поделиться
Скачать
Evolve SHOWROOMS Скачать руководство пользователя страница 36

EVOLVE

Page 

36 • 

evolvefurnituregroup.com

Worksurface Supporting Pedestals

Parts List

1 Worksurface-supporting pedestal

According to your plan, select the type of pedestal which is going 
to be used as a worksurface support. Identify which side of the 
pedestal is to be attached to the panel slots and install the panel 
mounting bracket accordingly.

STEP 1: Align the outer corner of the bracket with the outer corner 
of the pedestal, just below the top lip. “A”

STEP 2: Hold the bracket in position and drive the supplied four 
self-drilling screws through the bracket into the rear wall of the 
pedestal.

STEP 3: Screw the glides all the way into the pedestal.

STEP 4: Hook the pedestal into the panel and tap with a rubber 
mallet to ensure that the bracket is securely engaged in the panel 
slots.

STEP 5: Remove drawers.

STEP 6: Adjust all pedestal levelers while making sure that the 
bracket did not disengage from the panel.

Proceed with the installation of the worksurfaces.

STEP 7:Predrill holes at suggested locations. Fasten the pedestal 
by driving three screws through the pedestal into the worksur-
face.

INSTALLATION GUIDELINES

Содержание SHOWROOMS



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды