Evolve SHOWROOMS Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 58

background image

EVOLVE

evolvefurnituregroup.com • Page

31

Ceiling Power Entry

Parts List

1 Ceiling Power Entry

A Ceiling Power Entry is used to connect the electrical distribu-
tion system to the building power network at an above ceiling
level junction box. The Ceiling Power entry is installed by plug-
ging directly into a Power Distribution Housing. The procedure is
similar to Jumper Cable/Pass- Through Cable installation and the
connection is the same.

Ensure that all panels are mechanically connected prior to elec-

trical connection.

STEP 1: Locate the appropriate connection point in the panel
raceway channel. The raceway cover must be removed to allow
installation.

STEP 2: Locate nearest corner post and remove center portion
only of
two piece post top cap. (Use PVC top cap EVCPC01

STEP 3: Identify proper length of post extension. (Cut to desired
length if necessary.) Make sure that post extension will extend
above ceiling tile.

STEP 4: Cut hole (slightly larger than the post extension) in ceiling
tile directly above the corner post.

STEP 5: Slide post extension through cut-out in ceiling tile and
mechanically attach it to the corner post through the top cap.

STEP 6: Feed the open end of the Ceiling Power Entry assembly
from the raceway channel to the ceiling through a corner post and
post extension.

STEP 7: Position the Ceiling Power Entry assembly at the end
of the appropriate Power Distribution Housing and plug them
together. Be sure the parts are fully seated and latched to assure
proper electrical connection and mechanical security.

STEP 8: Replace the raceway cover.

It is recommended that installation of the electrical harness

be made under the supervision of a licensed electrician in ac-

cor- dance with applicable codes and regulations. Refer to the

wiring schematic attached to the conduit and shown in this

Installation Manual. Always determine that harness is electri-

cally connected to only one power supply.

INSTALLATION GUIDELINES

«
...
29
30
31
32
33
...
»

Содержание SHOWROOMS



























































Отзывы:

Нет отзывов

Похожие инструкции для SHOWROOMS

Бренд: 3M Страницы: 2

Бренд: Raymarine Страницы: 90

Бренд: Zenbooth Страницы: 60

Бренд: Pahlen Страницы: 20

Бренд: Paia Страницы: 7

Бренд: Guyatone Страницы: 2

INTEGRA ARINC e-NAV

Бренд: Kannad Страницы: 20

Бренд: Meritor Страницы: 65

Einthoven CR1000

Бренд: ACE Solution Страницы: 29

Бренд: NTN Страницы: 19

Бренд: Baileigh Страницы: 39

Бренд: Abus Страницы: 2

Бренд: M-system Страницы: 2

Бренд: Sanity Страницы: 40

Бренд: Zhermack Страницы: 200

Red Chili D 1418

Бренд: M&R Страницы: 45

Бренд: Tegam Страницы: 27

Бренд: K-SPORT Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды