evertz 570NAT-HW-X19 Скачать руководство пользователя страница 55

Страница: 55 / 56

570NAT-HW-X19

High Density Network Address Translator

Revision 1.0

Page - 45

UPGRADE PROCEDURE

5.1. WEB INTERFACE - FIRMWARE UPGRADE

Using the Web interface is the fasted and recommended procedure to load the firmware onto the

570NAT-HW-X19.

When first visiting the 570NAT-HW-X19 web interface, the user will be asked to enter a Login and

Password. Enter “

root

” for Password and “

evertz

” for Login.

On the top of the web page for the 570NAT-HW-X19, there is a tab labeled

Upgrade

. The

Upgrade

tab

is used to check current firmware version and upload the latest firmware.

Figure 5-1: WebEASY

- Upgrade Button on Top Menu Bar

Selecting the Upgrade tab, will take you to Figure 5-2 where the current firmware version is shown.

Should the firmware version be outdated, you will need to download the firmware image file.



NOTE: Contact Evertz to get the latest firmware image file.

Figure 5-2: WebEASY

- Firmware Upgrade Menu

Click

Choose File

and browse to locate

image

file. Once selected, click

Open

to advance to next step.

Click

Upgrade

and watch progress bar for status. Once completed, the device will automatically restart.

Содержание 570NAT-HW-X19

























































Результаты поиска

Содержание 570NAT-HW-X19

Отзывы:

Похожие инструкции для 570NAT-HW-X19

Бренды по названию

Популярные бренды

evertz 570NAT-HW-X19, Руководство пользователя

Результаты поиска

Содержание 570NAT-HW-X19

Отзывы:

Похожие инструкции для 570NAT-HW-X19

Бренды по названию

Популярные бренды