evertz 570NAT-HW-X19 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 56

background image

570NAT-HW-X19

High Density Network Address Translator

Revision 1.0

Page - 33

4.6.4. WAN to LAN: Input Flow Configuration

Flows 1 to 256

Mode:

This control allows the user to enable De-Encap/NAT or disable WAN to LAN for this flow.

Input Destination IP Address:

This control allows the user to set the Input Destination IP address of

the packets to be received.

Input Destination UDP Port:

This control allows the user to set the Destination UDP Port number to

be received.

VLAN:

This control allows the user to assign this flow to a VLAN.

SSM Filter:

This control allows the user to enable Source Specific Multicast (SSM) channel based

filtering.

Input Source IP Address:

This control is used in NAT mode to configure the output header with the

desired source IP address.

Input Bitrate:

This monitor will display the bit rate of the streams that are being received in kbps.

Input Bitrate Cap:

This control allows the user to set a cap on the bitrate for each flow in Kbps.

4.7. LINK AGGREGATION

Figure 4-14: WebEASY

®

- Link Aggregation

Link aggregation allows users to direct the flow of data through WAN port – CORE – LAN port by

assigning which WAN port is assigned to each core, and which LAN port is assigned to each core. This

«
...
41
42
43
44
45
...
»

Содержание 570NAT-HW-X19

























































Отзывы:

Нет отзывов

Похожие инструкции для 570NAT-HW-X19

Бренд: Yamaha Страницы: 22

Refresh-o-mat HD

Бренд: Waeco Страницы: 300

Бренд: Yamaha Страницы: 1

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 12

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 12

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 48

Бренд: Yamaha Страницы: 50

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 85

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 107

Бренд: Yamaha Страницы: 127

Бренд: Yamaha Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды