Everlasting BAKING CAB FB 100 Скачать руководство пользователя страница 33

Страница: 33 / 56

ENGLISH

List of alarms which may occur:

ALARM

DESCRIPTION

CAUSE

SOLUTION

Pr1

Cell probe error

• Cell probe fails

• Replace probe

Pr2

Evaporator probe error

• Evaporator probe fails

• Replace probe

Pr3

Condenser probe error

• Disabled

Pr4

Humidity probe error

• Humidity probe is faulty

• Replace the probe

Maximum temperature

alarm

• Cell probe is faulty

• Control unit is faulty

• Cooling system is faulty

• Service

Poup-Down

compressor alarm

• Disabled

CSd

Blocked Compressor alarm • Disabled

• Disabled

COH

Blocked Compressor alarm • Disabled

• Disabled

rtc

Internal clock error

• The device has not worked

for a long period

• Control unit is faulty

• Switch on the device

and set the date again

• Service

CtH

Compressor thermal

protector

• Disabled

ErC

No compatibility between

interface and control modu-

• Firmware of setting - instrument

is not compatible

• Service

ErL

No communication between

interface and control module

• Interface connection is either

incorrect or faulty

• Check proper

connection

Interruption of power supply

to the machine

• Power failure may have

occurred

• Press any key to cancel

the alarm

Open door alarm

• The door has been kept open • Close the door

High pressure alarm

• Disabled

Low pressure alarm

• Disabled

Содержание BAKING CAB FB 100

























































Результаты поиска

Содержание BAKING CAB FB 100

Отзывы:

Everlasting BAKING CAB FB 100, Руководство по эксплуатации и обслуживанию, Страница: 33 / 56

Результаты поиска

Содержание BAKING CAB FB 100

Отзывы: