Ever SINLINE RT Скачать руководство пользователя страница 6

Страница: 6 / 75

EVER UPS SINLINE RT / RT XL series instruction manual

2017-04-26 12:41

Pomoc Techniczna, tel.: +48 61 6500 400

www.ever.eu

SAFETY INSTRUCTIONS AND RECOMMENDATIONS

A) General remarks

CAUTION!

Before starting the procedures described in this manual,

please read the general safety instructions (including the instructions

found in this document), health & safety information, environmental

protection information and legal regulations that may apply. Always

observe the instructions and recommendations in these documents.

CAUTION!

The user is strictly forbidden from performing any repairs, as

this would constitute a health hazard and may result in death. Any

repairs and replacement of batteries should be carried out only by

suitably qualified service technicians with professional licenses required

by law.

CAUTION!

The unit should be operated and stored in conditions

complying with the requirements set in the specification (technical

documentation).

CAUTION!

The device is completely disconnected from the mains only

when the power lead is removed from the mains socket (the plug is

removed from the mains socket).

CAUTION!

The unit is equipped with an internal power source (batteries)

or it may operate in combination with a fixed, external source of power

(battery packs). Dangerous voltage may be present at the output

terminal(s), even if the unit has been disconnected from the mains.

CAUTION!

The user should place warning labels on all remotely

installed primary isolation switches in order to warn electrical service

technicians that the circuit is powered by a UPS unit. The following (or

equivalent) text should be used on such warning labels:

DISCONNECT THE UPS SYSTEM BEFORE STARTING WORK ON THIS

CIRCUIT.

Содержание SINLINE RT












































































Результаты поиска

Содержание SINLINE RT

Отзывы:

Похожие инструкции для SINLINE RT

Бренды по названию

Популярные бренды

Ever SINLINE RT, Инструкция по эксплуатации

Результаты поиска

Содержание SINLINE RT

Отзывы:

Похожие инструкции для SINLINE RT

Бренды по названию

Популярные бренды