Ever SINLINE RT Скачать руководство пользователя страница 51

Страница: 51 / 75

EVER UPS SINLINE RT / RT XL series instruction manual

www.ever.eu

Pomoc Techniczna, tel.: +48 61 6500 400

2017-04-26 12:41

In case of the rack version UPS and the battery module, remove the battery

module from the cabinet.

CAUTION!

If only the UPS is used, use the menu (MENU;

CONFIGURATION; UPS; Number of EBMs) to change the number of

battery modules from 1 to 0. If no battery module is connected to the

UPS, leaving the value as 1 may cause serious damage to the UPS unit's

battery.

FIRST START-UP OF THE UPS

To avoid the overload alarm, before starting the UPS, check if the total value of rated

powers of the devices to be connected (receivers) does not exceed the rated power

of the UPS. You can then proceed to carry out subsequent installation steps:

Install the UPS (tower or rack version) and place the UPS in its intended location.

If the optional battery module is installed, make sure it is connected correctly.

Connect the UPS to the mains socket with a power cord.

Press and keep the key on the UPS unit's front panel depressed for over 1

second to switch the device on. The LCD will show the welcome screen (EVER

Power Systems).

If the rack version of the UPS is installed, use the menu to set the display's mode

to rack (MENU; CONFIGURATION; DISPLAY; RACK/TOWER Mode).

Make sure the UPS is in the READY mode. To charge the UPS unit's battery

leave the UPS connected to the mains for at least 4 hours. If a battery module is

connected to the UPS, use the menu to configure the number of battery modules

(MENU; CONFIGURATION; UPS;Number of EBMs.)

CAUTION!

If no battery module is connected to the UPS, leaving the

value as 1 may cause serious damage to the UPS unit's battery.

Connect the devices you want to power (e.g. a PC with a monitor) to the UPS

unit's output sockets,

Switch on the UPS logically with the control panel (MENU; CONTROL; UPS

Enabled).

Switch the devices connected to the UPS on.

Содержание SINLINE RT












































































Результаты поиска

Содержание SINLINE RT

Отзывы:

Похожие инструкции для SINLINE RT

Бренды по названию

Популярные бренды

Ever SINLINE RT, Инструкция по эксплуатации

Результаты поиска

Содержание SINLINE RT

Отзывы:

Похожие инструкции для SINLINE RT

Бренды по названию

Популярные бренды