manualshive.com logo in svg

Eurotherm TE200S, Руководство пользователя, Страница: 37 / 42

Поделиться
Скачать
Eurotherm TE200S Скачать руководство пользователя страница 37

5-3

TE200S User manual

MAINTENANCE

To protect the thyristors in the TE200S, depending on the wiring configuration the following

combinations may be used:
• Two ‘single-phase fuse and fuseholder’ assemblies installed in the controlled phases or
• One ‘three-phase fuse and fuseholder’ assembly installed between the TE200S SSR and 

the cable protection and mains circuit breaker; in the direct phase it is possible to install a 
solid link instead of a fuse.

References for the ‘fuse and fuseholder’ assemblies and for spare fuses are given in the 
following tables.

Nominal Spare 

fuse

Code

current

References:

Fuse+fuseholder

Dimensions

TE200S Fuse

Eurotherm

Ferraz

Assembly

(mm)

16A

20A

CH 260024

K330013

FU1038/16A/00

81 x 17.5 x 68

25A

30A

CH 260034

M330015

FU1038/25A/00

81 x 17.5 x 68

40A

50A

CH 330054

B093910

FU1451/40A/00

95 x 26 x 86

50A

63A

CS 173087U063

T094823

FU2258/50A/00

140 x 35 x 90

63A

80A

CS 173246U080

W076310

FU2760/63A/00

150 x 38 x 107

Table 5-1  Recommended high-speed fuses for thyristor protection

Single-phase fuseholders.

Nominal Spare 

fuse

Code

current

References:

Fuse+fuseholder

Dimensions

TE200S Fuse

Eurotherm

Ferraz

Assembly

(mm)

16A

20A

CH 260024

K330013

FU3038/16A/00

81 x 52.5 x 68

25A

30A

CH 260034

M330015

FU3038/25A/00

81 x 52.5 x 68

40A

50A

CH 330054

B093910

FU3451/40A/00

95 x 79 x 86

50A

63A

CS 173087U063

T094823

FU3258/50A/00

140 x 108 x 90

63A

80A

CS 173246U080

W076310

FU3760/63A/00

150 x 114 x 107

Table 5-2  Recommended high-speed fuses for thyristor protection

Three-phase fuseholders with three fuses.

Maximum operating voltage for fuses: 500Vac (line-to-line).

Содержание TE200S











































Отзывы:

Нет отзывов