Eurotech AIM104-COM8 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 25

background image

AIM104-COM8 Technical Manual

About this manual

© 2007 Eurotech Ltd Issue C

6

About this manual

This manual describes the operation and use of the AIM104-COM8 PC/104 module.
It is both a reference and user manual and includes information about all aspects of the
module.

Conventions

Symbols

The following symbols are used in this guide:

Symbol Explanation

Note - information that requires your attention.

Tip - a handy hint that may provide a useful alternative or save
time.

Caution – proceeding with a course of action may damage
your equipment or result in loss of data.

Terminology

To prevent confusion with the standard PC AT nomenclature of COM1-4, this manual
refers to the channels on the AIM104-COM8 as 0-7. Where this manual specifies
COM1-4, this refers to the standard PC AT communications ports.

«
...
4
5
6
7
8
...
»

Содержание AIM104-COM8


























Отзывы:

Нет отзывов

Похожие инструкции для AIM104-COM8

Бренд: SOYO Страницы: 95

TPS628436-7-8EVM-167

Бренд: Texas Instruments Страницы: 15

Бренд: BiPOM Electronics Страницы: 12

NB7NPQ1102MCMUGEVB

Бренд: onsemi Страницы: 7

Бренд: Biostar Страницы: 118

Бренд: Intel Страницы: 92

Бренд: Seanix Страницы: 49

Бренд: Supermicro Страницы: 93

Бренд: Gigabyte Страницы: 44

Бренд: Texas Instruments Страницы: 24

Бренд: TYAN Страницы: 117

Бренд: IMS Страницы: 14

Бренд: SOYO Страницы: 104

Бренд: AvaLAN Страницы: 14

Бренд: Toyama Страницы: 48

Бренд: ASROCK Страницы: 113

Бренд: Linear Technology Страницы: 7

Бренд: Linear Technology Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды