Eurotech AIM104-COM8 Скачать руководство пользователя страница 4

Страница: 4 / 25

AIM104-COM8 Technical Manual

Introduction

The AIM104-COM8 is an 8-bit or 16-bit PC/104 module that provides up to eight
RS232 asynchronous communications channels.

Variants

There is only one standard variant of the this board:

•

AIM104-COM8 : Eight channel RS232 PC/104 board.

A four channel version of the board may also be available for volume orders.
Please contact the Eurotech Ltd sales team for information on this variant.

Features

•

Eight 16C550 compatible UART channels.

•

Transfer rates up to 115.2Kbaud supported.

•

+5V only operation.

•

All channels can appear as a block anywhere in I/O address range 000-3FFh.

•

First four channels can be individually set as standard PC/AT COM1-4.

•

Each QUART (Quad-UART) can drive one link-selectable IRQ in the range 3, 4,
5, 7, 9, 10, 11, 12, 14, 15.

•

The two QUART interrupts can be combined to drive one IRQ.

•

PC/104 16 bit interface (but can be used in 8-bit slot if IRQ10, 11 and 15 are not
required).

•

Zero wait state bus operation capability.

•

Board access LED.

•

Interrupt activity LED.

•

TxD/RxD activity indicator LEDs on all channels.

•

Power requirements:

220 mA (typical) at +5V DC.

•

Temperature range:

-20°C (-4°F) to +70°C (158°F) operating.

-40°C (-40°F) to +125°C (125°F) storage.

Содержание AIM104-COM8


























Результаты поиска

Содержание AIM104-COM8

Отзывы:

Похожие инструкции для AIM104-COM8

Бренды по названию

Популярные бренды

Eurotech AIM104-COM8, Техническое руководство

Результаты поиска

Содержание AIM104-COM8

Отзывы:

Похожие инструкции для AIM104-COM8

Бренды по названию

Популярные бренды