Eurotech AIM104-COM8 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 25

background image

AIM104-COM8 Technical Manual

Jumpers

© 2007 Eurotech Ltd Issue C

14

JP2 - Group base address selection

The JP2 jumper is used to set the I/O base address for the serial ports. The default
jumper settings configure all of the serial ports at a 64-byte contiguous I/O space from
this address location.

The base address is always decoded to a 16-byte boundary. Fitting the link sets the
address line to zero for the decode. Leaving the link off means that the corresponding
address line must be a logic ‘1’ to select the board.

JP2

Line

Function when fitted

A9

Sets A9 in I/O address decode to 0

A8

Sets A8 in I/O address decode to 0

A7

Sets A7 in I/O address decode to 0

A6

Sets A6 in I/O address decode to 0

A5

Sets A5 in I/O address decode to 0

A4

Sets A4 in I/O address decode to 0

The default base address is 0x100, to avoid conflicts with common PC I/O maps.
In order to achieve this fit all links apart from A8. Check your system I/O map for
conflicts before use.

«
...
12
13
14
15
16
...
»

Содержание AIM104-COM8


























Отзывы:

Нет отзывов

Похожие инструкции для AIM104-COM8

Бренд: Sun Microsystems Страницы: 74

JetBox 9310 Series

Бренд: Korenix Страницы: 21

Бренд: Advantech Страницы: 90

Бренд: Oki Страницы: 24

Бренд: ASROCK Страницы: 2

Бренд: Mini-Itx Страницы: 174

Бренд: Analog Devices Страницы: 128

8A 72QFN Series

Бренд: IDT Страницы: 29

X58 Classified3

Бренд: EVGA Страницы: 2

Бренд: Gigabyte Страницы: 23

Бренд: Texas Instruments Страницы: 28

Бренд: EPOX Страницы: 55

Бренд: Gigabyte Страницы: 96

Бренд: Abit Страницы: 134

Бренд: DFI Страницы: 76

Бренд: SOYO Страницы: 29

Бренд: DFI Страницы: 101

Бренд: Digilent Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды