Euromate 482274, Оригинальное руководство пользователя

Страница: 36 / 144

GB
36
– Cut large strips of adhesive gripping tape to the
dimensions of the window.
– Glue them to the frame of your window and then
do the same on the inner surface of the window
flap (on the side of the handle).
►
P. 6, item 14
– Glue the widest side (A) of the large white fabric
piece to the window frame and then glue the nar-
rower side (B) to the window leaf (handle side)
from the center, then up and finally down.
– Close the window and make sure the large fabric
piece is not stuck in the closing seams and the
window closes always correctly, even with the
tapes sticky adhesive tape.
►
P. 6, item 15
– Open the window gently and open the zipper of
the fabric piece (at level of the bottom or middle of
the window) then insert the exhaust duct into the
opening.
– Readjust the zipper so that the exhaust duct is
attached so that there is no air exchange between
the inside and the outside.
►
P. 6, item 16
– Your caulking kit is now installed, you can now
turn on and enjoy the coolness of your mobile air
conditioner!
– If you no longer want to use your mobile air con-
ditioner and close your window, you can simply
remove the sheath from the zipper and close your
window, in verifying that the fabric piece is not
stuck in the closing seals.
Operation
►
Operation – p. 7
Before use, familiarise yourself thoroughly with the
operating panel and the remote control as well as
their functions. You can then use the icons as orien-
tation for the desired functions. The device can be
operated via the operating panel on the device or
using the remote control.
The operating panel of the air conditioning unit
►
P. 7, item 1
A. Power on/off
B. Fan speed
C. Temperature up
D. Temperature down
E. Operation mode
F. Timer on/off
G. Swing on/off
H. Sleep mode
1. Cooling
2. Dehumidifying
3. Fan
4. WIFI
5. High fan speed
6. Medium fan speed
7. Low fan speed
8. Water full
Remote control
►
P. 7, item 2
1. [POWER] : Power on/off
2. [TIMER] : Timer on/off
3. [MODE] : Operation MODE
4. [TEMP-] : Temperature down
5. [TEMP+] : Temperature up
6. [SPEED] : Fan speed
7. [Sleep] : Sleep mode
8. [SWING] : Auto swing
Operation Introduction
Before starting operations in this section:
– Find a place where there is power supply nearby.
►
P. 7, item 3
– As shown, install the exhaust hose, and adjust the
window position well.
►
P. 7, item 4
– Connect drain hose well (only for using heating
model);
– Insert the power cord into an grounded
AC220~240V/50Hz socket;
– Press the [POWER] button to turn on the air-con-
ditioner.
Cooling operation
– Press the [Mode] button till the [Cool] icon
appears.
– Press the [DOWN] or [UP] button to select a
desired room temperature. (16°C-31°C)
– Press the [WIND] button to select wind speed.
Dehumidifying operation
– Press the [Mode] button till the [Dehumidify]
icon appears.
– Automatically set the selected temperature to cur-
rent room temperature minus 2°C. (16°C-31°C)
– Automatically set the fan motor to [LOW] wind
speed.
Fan operation
– Press the [Mode] button till the [Fan] icon
appears.
– Press the [WIND] button to select wind speed.
Timer operation
Timer [ON] setting:
– When the air-conditioner is [OFF] , press
the [Timer] button and select a desired [ON] time
through the temperature and time setting buttons.
– [Preset ON Time] is displayed on the operation
panel.
– [ON] time can be regulated at any time in 0-24
hours.
– Press the [Timer] button again to confirm, Timer
indicator turns on.
– To deactivate the timer function, press [Timer]
button until timer indicator turns off.
Timer [OFF] setting
Note: If you have a window with French
opening with two leaves: Block the first leaf
with the handle and make the installation of
the caulking kit on the second leaf (without
the handle). Before installation, check that
the adhesive gripping tape do not damage
your window.
Note: Do not drop the remote controller. Do
not place the remote controller in a location
exposed to direct sunlight.