manualshive.com logo in svg

EUCHNER CES-AP-C01- Series, Руководство по эксплуатации

Поделиться
Скачать
EUCHNER CES-AP-C01- Series Скачать руководство пользователя страница 9

9

112663-05-03/15 (translation of the original operating instructions)

Operating Instructions

Non-Contact Safety Switch CES-AP-C01-…

EN

8.  Mounting

CAUTION

Safety switches must not be bypassed (bridging of contacts), turned away, removed or otherwise 

rendered ineffective.

 

Ì

Observe EN ISO 14119:2013, section 7, for information about reducing the possibilities for by-

passing an interlocking device.

NOTICE

Risk of damage to equipment and malfunctions as a result of incorrect installation. 

 

Ì

Safety switches and actuators must not be used as an end stop.

 

Ì

Observe EN ISO 14119:2013, sections 5.2 and 5.3, for information about fastening the safety 

switch and the actuator.

 

Ì

From the assured switch-off distance S

ar

, the safety outputs are safely shut down.

 

Ì

When mounting several safety switches, observe the stipulated minimum distance to avoid mutual 
interference.

.

min . 40 mm

 

Ì

If the actuator is installed flush, the switching distance changes as a function of the installation 
depth and the safety guard material.

Operating

distance

Actuator

Operating

distance

Actuator

Flush mounting

Surface mounting

Note the following points:

 

Ì

Actuator and safety switch must be easily accessible for inspection and replacement.

 

Ì

Actuator and safety switch must be fitted so that

 -the front faces are at the minimum switch-on distance 0.8 x S

ao

 or closer when the safety guard is closed. To avoid 

entering the area of possible side lobes, a minimum distance is to be maintained in case of a side approach direction. 

See chapter 

6. Technical data, 

section 

Typical operating distance

 of the respective actuator.

 -when the safety guard is open up to the distance S

ar

 (assured switch-off distance), a hazard is excluded.

 -the actuator is positively mounted on the safety guard, e.g. by using the safety screws included.

 -they cannot be removed or tampered with using simple means. 

 

Ì

Pay attention to the maximum tightening torque for the read head or safety switch and actuator mountings of 1 Nm.

Содержание CES-AP-C01- Series

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды