ETI 004656570, Техническое руководство по установке

Страница: 6 / 16

6 / 16
Advance Set-up Menu:
PARAMETER DESCRIPTION RANGE DEFAULT
$$ .
Mains Connection 0 = Three-Phase 1 = Single-Phase 0 … 1 0
$$ .
*
Sense of CT current
1 = CT on L1 Direct 2 = CT on L1 Inverse
1 … 6 1 3 = CT on L2 Direct 4 = CT on L2 Inverse
5 = CT on L3 Direct 6 = CT on L3 Inverse
$ .
Frequency 1 = 50 HZ 2 = 60 HZ 1 … 2 1
$ .
Serial interface TTL 0 = Disable 1 … 99 = Enable 0 … 99
1
**
$ .
Temperature Alarm 0 = Disable 35 … 158 = Enable 0 / 35 … 158 45 (°C)
$ .
Temperature scale 0 = °C 1 = °F 0 … 1 0
$ .
Alarm THD (%) I 5 … 200 120
$ .
THD(%) Delay on (seconds) 1 … 600 5
$ .
Alarm relay
(see Table pag.10)
0 = None
1 = All 2 = $$ . ++8
3 = $$ . //8
4 = $$ . ++,
5 = $$ . //,
6 = $$ . ++&
7 = $$ . //&
8 = $$ . 77+
9 = $$ . &&6
0 … 9 1
$ .
Time to switch off all the capacitors because of low current (seconds). 1 … 240 120
$ .
Min Temp. to switch off the fan relay output. (if selected °F set the right value) 1 … 240 30
$ .
Max Temp. to switch on the fan relay output. (if selected °F set the right value) 1 … 240 50
$ .
Mains Three Phase Voltage.
220 … 440
with step of 5
400
$ .
Fixed step selection (0=none) 0 … 12 0
$ .
0 = kvar with subtraction fixed step 1 = Real kvar 0 … 1 1
$ .
Serial Protocol Type
0 Proprietary 9600 Bds EVEN 1 Bit Stop
0 … 15 0
1 Modbus 19200 Bds EVEN 1 Bit Stop
2 Modbus 9600 Bds EVEN 1 Bit Stop
3 Modbus 4800 Bds EVEN 1 Bit Stop
4 Modbus 2400 Bds EVEN 1 Bit Stop
5 Modbus 1200 Bds EVEN 1 Bit Stop
6 Modbus 19200 Bds ODD 1 Bit Stop
7 Modbus 9600 Bds ODD 1 Bit Stop
8 Modbus 4800 Bds ODD 1 Bit Stop
9 Modbus 2400 Bds ODD 1 Bit Stop
10 Modbus 1200 Bds ODD 1 Bit Stop
11 Modbus 19200 Bds NONE 1 Bit Stop
12 Modbus 9600 Bds NONE 1 Bit Stop
13 Modbus 4800 Bds NONE 1 Bit Stop
14 Modbus 2400 Bds NONE 1 Bit Stop
15 Modbus 1200 Bds NONE 1 Bit Stop
16 Proprietary 9600 Bds NONE 1 Bit Stop
17 Proprietary 4800 Bds NONE 1 Bit Stop
$ .
Anti-Hunting 0 = Disable 0.90 … -0.95 = Enable 0 / 0.90 … -0.95 0
$ .
Threshold for Cos
M
alarm 0 = Disable 0.50 … 0.95 = Enable 0 / 0.50 … 0.95 0
$ .
Delay between steps Switch-ON / Switch-OFF (in sec. with step of 0.1) 1.00 … 5.00 1.00
*
When the
$ .
value is displayed, by pressing together and , the updated Cos
M
it’s immediately shown.
**
The values 1 to 99 indicate the device number when the units are connect on a serial interface, the values 100 to 199 aren’t used.
5.3 TO SET DEFAULT PARAMETERS:
- In
$ .
parameter, press all buttons together for 5 seconds, on display will shows
6$8
Now the device will restart.
ATTENTION: All settings made on the device will be lost and all steps will be restored to default setting.
ETI Elektroelement d.d. - Slovenija
Tel.: 03/56-57-570- Fax: 03/56-74-077
www.eti.si - eti@eti.si