Etel DSC2P Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 44

Etel DSC2P Скачать руководство пользователя страница 6

ETEL Doc.- Hardware Manual # DSC2P / Ver H / 6/1/11

DSC2P Hardware Manual

5

Record of revisions concerning the DSC2P manual:

Documentation concerning the DSC2P:

•

DSC2P Hardware Manual

(Specifications & electrical interfaces)

# DSC2P 904 H

•

Operation & Software Manual

(DSC2P's setup, use & programming)

# DSC2P 903 x

•

DSO-PWS User's Manual

(Power module installation and specifications)

# DSOPWS 902 x

•

DSO-RAC2 Hardware Manual

(DSO-RAC2 principle)

# DSORAC2 904 x

•

EBL2 Communication Manual

(EBL2 principle, messages mapping)

# EBL2 908 x

Remark:

By default, the DSC2P is delivered without UL recognition.

Document revisions

Issue (x)

Date

Modified

beta

23.08.00

Specifications, preliminary

Ver A

26.01.01

First version

Ver B

19.09.01

Updated version (update of the motor connection and DIP switch)

Ver C

12.09.03

Updated version
- New rack format: DSC2Px41-xxx (refer to

§2.1.3

)

- New housed format (refer to

§2.2

and

§3.5

)

- Brake resistor as well as power stage and short-circuit relay on housed format (refer to

§3.5.2

,

§3.5.3

and

§3.5.4

)

- Additional safety precautions in accordance with the UL & CE standards

Ver D

19.02.04

Updated version
- Housed format is UL certified

Ver E

31.03.04

Updated version
- Housed format dimensions modified

Ver F

02.09.04

Updated version
- New rack format: DSC2Px11-xxx (refer to

§2.1.3

)

Ver G

19.12.05

Updated version
- New signals on JC4 connector (

§3.3.4

)

- Additional detailed descriptions

Ver H

06.01.11

Updated version:
- New UL certification laboratory (TUV)

The DSC2P position controllers have been successfully tested and evaluated to
meet the UL 508C for US market and CSA-C22.2 N°14-05 for canadian market.

This standard describes the fulfillment by design of minimum requirements for
electrically operated power conversion equipment which is intended to eliminate the
risk of fire, electrical shock, or injury to persons being caused by such equipment.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
4
5
6
7
8
...
»

Содержание DSC2P













































Отзывы:

Нет отзывов