manualshive.com logo in svg

Etel DSC2P, Руководство по оборудованию, Страница: 35 / 44

Поделиться
Скачать
Etel DSC2P Скачать руководство пользователя страница 35

34

DSC2P Hardware Manual

ETEL Doc. - Hardware Manual # DSC2P / Ver H / 6/1/11

3.4

Motor connector

 Warning:

High voltage may be present on the motor connector.
Before connecting or disconnecting the motor cable or touching the controller,

 turn

off all the power supplies

 

and wait 10 minutes

 to allow the internal DC bus

  

capacitors to discharge.

 

 

Caution:

The motor connector must be insulated (no contact) from the power and the mains.
The motor connector must always be correctly screwed onto the DSC2P to respect
the EMC standard.

Caution:

The motor connector must be handled in an ESD protected environment, only.

Remark: 

The motor cable connected to the DSC2P must be shielded (see 

§3.7.1

).

3.4.1

ETEL motor cable numbering system

ETEL standard motors cables are numbered according to the following system:

3.4.2

Connector JC7: Motor connection

The DSC2P can drive single-phase, two-phase and three-phase motors. Connector JC7 enables the supply of
the motor phase(s).

(*): With two-phase motor, the current in 'motor phase 1- / 2-' is equal to (

√

2 x motor phase 1+) or (

√

2 x motor

phase 2+). Be careful to use the suitable cable diameter.

Three-phase motors

Designation

Function

1 or U1

Motor phase 1

2 or VV2

Motor phase 2

3 or WWW3

Motor phase 3

Green / Yellow

Protective earth

Phoenix Contact PC 4/4-G-7,62 (plastic connector)

M

OTOR

CONNECTION

Pin #

Signal

Function

1-phase motor

2-phase motor

3-phase motor

1

PE

Protective earth

Protective earth

Protective earth

2

PH3

Do not connect

Motor phase 2 +

Motor phase 3

3

PH2

Motor phase -

Motor phase 1 - / 2 - (*)

Motor phase 2

4

PH1

Motor phase +

Motor phase 1 +

Motor phase 1

MOTOR

 

CONNECTI

O

N

4

1

JC7

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание DSC2P













































Отзывы:

Нет отзывов