background image

6

Source Four PAR Assembly Guide

Step 12: Hold the lens by the edge and position it so the wave side faces the rear of the 

fixture. Se

Figure 6

.

Step 13: From the top of the fixture, slide the lens behind the lens catchers and position it 

behind the tabs on the bottom of the lens rotator ring.

Step 14: Gently push the top of the lens inward until it snaps behind the spring clip.

Step 15: Install the lamp socket assembly (

See “Assemble lamp socket” on page 3.

) to the 

barrel housing assembly and secure with brass knurled screw on rear of lamp 

socket assembly.

Cleaning the reflector

Step 1:

Remove the lens to expose the reflector so you can access it from the front of the 

luminaire.

Step 2:

Remove dust with a blast of oil-free air or wipe with a clean, lint-free cloth. 

Isopropyl alcohol, distilled water or a 50%-50% mixture of each can be used to 

clean the glass surface.

Step 3:

Reinstall a lens before using the luminaire.

Cleaning the lens

Remove dust with a blast of oil-free air or wipe with a clean, lint-free cloth. Isopropyl alcohol, 

distilled water or a 50%-50% mixture of each can be used to clean the glass surface.

W A R N I N G :

Do not use ammonia-based or other harsh commercial cleaners. Clean 

reflector only as directed.
Commercially available glass cleaning agents should be avoided as they 

may contain ammonia, other harsh chemical detergents or abrasive agents. 

These cleaners may damage the glass surface and the Anti-Reflective 

coatings. Do not immerse or soak the glass in any cleaning solution.

W A R N I N G :

Do not use ammonia-based or other harsh commercial cleaners. Clean lens 

only as directed.
Commercially available glass cleaning agents should be avoided as they 

may contain ammonia, other harsh chemical detergents or abrasive agents. 

These cleaners may damage the glass surface and the Anti-Reflective 

coatings. Do not immerse or soak the glass in any cleaning solution.

Spring clip

Retaining clip

Lens Catcher

Spring clip

Retaining clip

Tab

Figure 6

Содержание Source Four PAR EA













Отзывы: