eta SH Touch Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 64

background image

53

2012-11

Heating circuit

Operating modes

SH Operation

On Screed

The heating circuit is in operation; the screed
drying program is being run.

Off Enable temp.

The heating circuit is still switched off because the
boiler is not yet able to supply sufficient heat. The
enable temperature for the heating circuit has not
yet been exceeded.

Off Target day

The heating circuit is switched off. The target flow
temperature calculated from the heating curve
"Day" is below the room temperature as measured
by the room sensor.
If the unit does not have a room sensor, the calcu-
lated target flow temperature is below 18°C.

Off Target night

The heating circuit is switched off. The target
flow temperature calculated from the heating
curve "Night" is below the room temperature as
measured by the room sensor.
If the unit does not have a room sensor, the calcu-
lated target flow temperature is below 18°C.

Off Target holiday

The heating circuit is within the set holiday time,
and thus switched off.
The target flow temperature calculated from the
heating curve "Night" is below the room tempera-
ture as measured by the room sensor.
If the unit does not have a room sensor, the calcu-
lated target flow temperature is below 18°C.

Off Room day

The heating circuit is within a time slot, but
switched off. The current room temperature is
higher than the set "Room target" temperature by
at least the "RoomOffDiff" temperature.

Off Hot water

The heating circuit is switched off because the hot
water is currently being heated.

Off Room night

The heating circuit is switched off and outside the
set time slots. The current room temperature is
higher than the stored set-back temperature by at
least the "RoomOffDiff" temperature.

Off Room holiday

The heating circuit is within the set holiday time,
and thus switched off. The current room tempera-
ture is higher than the stored set-back temperature
by at least the "RoomOffDiff" temperature.

Off Outside day

The heating circuit is switched off. The current
outside temperature is higher than the set tempe-
rature for "Day Heating threshold".

Off Outside night

The heating circuit is switched off. The current
outside temperature is higher than the set tempe-
rature for "Night Heating threshold".

Off Outside holiday

The heating circuit is within the set holiday
time, and thus switched off. The current outside
temperature is higher than the stored set-back
temperature.

Off Summer

The heating circuit is switched off. The only active
functions are the freezing protection and the boiler
pump's "anti-blocking protection", which runs at
midday every Saturday.

Off Sensor failure

The heating circuit is switched off due to a defect
in the flow temperature sensor.

«
...
51
52
53
54
55
...
»

Содержание SH Touch

































































Отзывы:

Нет отзывов

Похожие инструкции для SH Touch

Бренд: IDEAL Страницы: 8

Бренд: Camus Hydronics Страницы: 108

Бренд: Riello Страницы: 44

Бренд: Noritz Страницы: 38

EcoBlue 12 Heat ErP

Бренд: Baxi Страницы: 64

Бренд: Radijator Страницы: 32

Бренд: Nieco Страницы: 40

MEGAPREX N 1060N

Бренд: Lamborghini Caloreclima Страницы: 108

Vitodens 222-F B2TA series

Бренд: Viessmann Страницы: 196

Бренд: Immergas Страницы: 112

Бренд: Vocera Страницы: 64

Бренд: Atmos Страницы: 40

Бренд: ACV Страницы: 15

Бренд: HELIX Страницы: 82

Бренд: Giona Страницы: 20

Promax 15/2 HE Plus

Бренд: Potterton Страницы: 12

Promax 24 Combi ErP

Бренд: Potterton Страницы: 20

Бренд: Potterton Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды