eta SH Touch Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 64

eta SH Touch Скачать руководство пользователя страница 40

40

www.eta.co.at

Changing function block names

User interface

Changing function block names

Changing the names of
the function blocks

The names of the function blocks can be changed
at any time in order to make them clearer to you.
For example, the names of the heating circuits HC,
HC2 etc. can be changed to ground floor, upper
floor, parents, living room or similar.

Example: Renaming HC1 "Ground floor"

Even though this example uses a long name, it is

best to choose short names so that you can reach
all the function blocks without having to use the
arrow buttons.

Selecting heating circuit 1

Double-tap [HC] to rename this function block.

2

x

A small screen appears for this function block.

Tap the [Change Name] button. An on-screen
keyboard appears.

Changing the name using the keyboard

cancel

save

Use the keyboard to enter the new name for
heating circuit 1, in this example: FLOOR.
Then press the [ENTER] button to save the new
name.
The [ESC] button cancels the renaming process and
changes back to the previous name.

HC has now been renamed "FLOOR".

The names of all the function blocks can be

changed at any time.

«
...
38
39
40
41
42
...
»

Содержание SH Touch

































































Отзывы:

Нет отзывов