background image

4

www.eta.co.at

General information

General

1

General

1.1

General information

Copyright

All  contents  of  this  document  are  property  of  ETA
Heiztechnik  GmbH  and  are  protected  by  copyright.
Any  reproduction,  transfer  to  third  parties  or  use  for
other purposes is prohibited without written permission
from the owner.

Subject to technical changes 

We reserve the right to make technical modifications
without  notice.  Printing  and  typesetting  errors  or
changes of any kind made in the interim are not cause
for  claims.  Individual  configurations  depicted  or
described  here  are  only  available  optionally.  In  the
event of contradictions between individual documents
regarding delivery scope, the information in our current
price list applies.

Software Description

The software version described in this documentation
corresponds to the version valid at the time of publica-
tion.  The  software  version  installed  on  your  product
may differ from that described in this documentation.

A software update to a more recent version can
always  be  performed.  With  the  appropriate  au-

thorisation,  the  required  files  can  be  found  at
"www.eta.co.at".

Explanation of symbols

Instructions and information

Layout of safety instructions

SIGNAL WORD!

Type and source of danger

Possible effects

Measures for avoiding the danger

Types of safety instruction

CAUTION!

On non-compliance with this safety instruction, there is
a risk of material damage.

WARNING!

On non-compliance with this safety instruction, there is
a risk of physical injury.

DANGER!

On non-compliance with this safety instruction, there is
a risk of major physical injury.

Explanation of pictograms

Switch the boiler on/off with the mains 
switch.

Perform a visual check of the components.

Clean the components with a soft cloth, for 
example.

Remove deposits with a vacuum cleaner or 
an ash vacuum.

Remove deposits with the poker.

Remove deposits with the cleaning brush.

Replace the wear parts (e.g., seals) with new 
items.

Lubricate the components. The lubricant to 
use is listed in the respective step.

Mount the components (e.g., screws or nuts) 
by hand only, without tools.

Tighten the components (e.g., screws or 
nuts) with a tool.

Install the components with some force (e.g., 
the retaining tube or the Lambda probe).

Handle the components carefully, since they 
break very easily.

Measure or check dimensions or clearances 
on the components.

Mark the components so that the correct po-
sition can be determined, for example, when 
mounting.

Wear a protective mask to avoid damage to 
the airways.

Содержание 939058-001









































Отзывы: