Estate Swing E-S 1600 Series Скачать руководство пользователя | Manualshive

Страница: 38 / 50

background image

Operating Parameters Chart

Minimum Force

Medium-low Force

Medium-high Force

High Force

This parameter adjusts the sensitivity of the
electronic clutch system. The electronic clutch
system controls the anti-crushing auto-reverse
feature when a gate in motion makes contact
with an obstacle.

1.5 Second Offset

3 Second Offset

6 Second Offset

10 Second Offset

This parameter is for Dual gate opener sys-
tems ONLY. This determines how long the
second leaf will pause before moving to allow
the first leaf to separate and avoid obstructing
on the other leaf.
If using a Single gate opener system, the set-
ting will not affect your gate.

Disabled

Enabled

This parameter turns auto-close on or off. The
pause time for the auto-close is set during
movement programming.

OPEN
A

Opens/Closes/Opens...

Opens/Stops/Closes/Stops...

This parameter determines what an OPEN A
terminal command will result in. d1 is recom-
mended for safety.

Disabled

Enabled

This parameter is for use with multiple gate
users. If enabled, when the gate is opening it
can not be reversed by another open signal.

FORCE

DELAY

AUTO-

RECLOSE

CONDO

Disabled

Enabled

OVER-
PUSH

This parameter is for use with electric gate
locks. The gate will briefly push further closed
before opening to allow the lock to release.

Flashing Lamp

90 Second Courtesy Light

LAMP

This parameter is to determine between a
flashing or steady lamp. If not using a lamp the
setting will not affect your gate.

Continued on following page.

4.2

«
...
36
37
38
39
40
...
»

Содержание E-S 1600 Series



















































Отзывы:

Нет отзывов

Похожие инструкции для E-S 1600 Series

Бренд: Accessmatic Страницы: 39

AXOVIA 220B RTS

Бренд: SOMFY Страницы: 68

Бренд: FAAC Страницы: 14

Бренд: Richmond Страницы: 29

VIPER LED VIP10

Бренд: Key Automation Страницы: 116

Бренд: CAME Страницы: 80

Бренд: tau Страницы: 12

Бренд: vds Страницы: 50

Бренд: quiko Страницы: 42

Safety Signal 3850RGD

Бренд: Raynor Страницы: 40

Бренд: Chamberlain Страницы: 32

Whisper Drive Security+ 459950

Бренд: Chamberlain Страницы: 88

Бренд: Chamberlain Страницы: 8

TOROQUEMASTER PLUS

Бренд: Wayne-Dalton Страницы: 20

Бренд: Yale Страницы: 109

Бренд: FAAC Страницы: 4

Бренд: Beninca Страницы: 15

Бренд: Etdoor Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды