background image

This Installation document is available at no charge from:
- Your local Wayne Dalton Sales Center, or
- Online at 

www.Wayne-Dalton.com

, or

- By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box 

67, Mt. Hope, OH., 44660

©Copyright 2020

REV20_08/10/2020

Part Number

T a b l e   O f   C o n t e n t s

345574

PLEASE DO NOT RETURN THIS PRODUCT 

TO THE STORE

If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the 
prompts to contact a customer service 
representative. They will be happy to handle 
any questions that you may have.

Pre-Installation 2

Important Safety Instructions 

2

Removing an Existing Door and Preparing the Opening 

2

Package Contents 

3

Door Section Identification 

4

Tools Required 

4

Breakdown Of Parts 

5

Door Installation Instructions 

6

Counterbalance Installation Instructions 

9

Optional Installation 

15

TorqueMaster

®

 Plus Reset Instructions 

15

Door Arm Hookup 

15

Inside Lock 

15

Pull Down Rope 

16

Maintenance 17

Cleaning Your Garage Door 

17

Maintaining The Finish On Your Garage Door 

17

Operation And Maintenance 

17

Warranty 18

Wayne Dalton, a division of Overhead Door Corporation

Model 9800

T

o r q u e

M

a s T e r

®

  P

l u s

I

nsTallaTIon

 I

nsTrucTIons

 a

nd

 o

wner

s

 

M

anual

r

esIdenTIal

 

 

s

Tandard

 l

IfT

To avoid possible injury, read and fully understand the enclosed 
instructions carefully before installing and operating the garage door. Pay 
close attention to all warnings and notes. After installation is complete, 
fasten this manual near garage door for easy reference.

IMPORTANT NOTICES!

Summary of Contents for TOROQUEMASTER PLUS





















Reviews: