Estate Swing E-S 1600 Series Скачать руководство пользователя

Страница: 50 / 50

Photo Eye, Safety Edge, Safety Loop:



Normally Closed (NC) of safety device

= FSW CL ter minal of CN4 block on gate opener

control board.



Common (COM) or Ground (GND) of safety device

= COM ter minal of CN4 block on gate

opener control board.



24V Power positive (+) or (24V) or (PWR) of safety device

= 24V+ ter minal of CN1 block

on gate opener control board.



24V Power negative (-) or (GND) or (PWR) of safety device

= 24V- terminal of CN1 block

on gate opener control board.

*Remove safety jumper from FSW CL terminal if using a safety device.

Solenoid Gate Lock:



Positive Lead of lock

= ELS terminal of CN2 block on gate opener control board.



Negative Lead of lock

= ELS terminal of CN2 block on gate opener control board.



Magnetic Gate Lock:

Magnetic gate locks must have their own power supply and their own

relay.



Coil of relay for magnetic lock

= ELS terminal of CN2 block on gate opener control board.



Coil of relay for magnetic lock

= ELS terminal of CN2 block on gate opener control board.

Connect positive lead of the power supply directly to the positive lead of the mag lock.

Connect negative lead of the power supply to the N/C terminal of the relay.

Connect the COM terminal of the relay to the negative lead of the mag lock.

Accessories Wiring

6.5

Содержание E-S 1600 Series



















































Результаты поиска

Содержание E-S 1600 Series

Отзывы:

Похожие инструкции для E-S 1600 Series

Бренды по названию

Популярные бренды

Estate Swing E-S 1600 Series, Инструкция по эксплуатации

Результаты поиска

Содержание E-S 1600 Series

Отзывы:

Похожие инструкции для E-S 1600 Series

Бренды по названию

Популярные бренды