Essilor AKR 550 Скачать руководство пользователя страница 56

Страница: 56 / 62

12-6 Replacement of joystick handle and measurement switch

1) Unscrew 1 fixation screw, and then remove

the joystick handle by pulling it up.

Joystick handle

2) Remove the measurement switch by pulling it to the direction B.
3) Remove the hexagon nut which fixes the measurement switch,

and then remove the measurement switch.

4) Remove the harness connected to the terminal of the

measurement switch (remove the heat shrinkable tube and
solder)

5) Fix new measurement switch and reconnect the harness.

(Connect the No. indicated on the measurement switch with the C
terminal. Make sure to reconnect the heat shrinkable tube.)

Cap

＊

For assembling, follow the reverse procedures.

Hexagon nut

Toothed lock washer

Plain washer

‘A’ unit

Details of ‘A’ unit

Measurement switch

Содержание AKR 550































































Результаты поиска

Содержание AKR 550

Отзывы:

Похожие инструкции для AKR 550

Бренды по названию

Популярные бренды

Essilor AKR 550, Руководство по обслуживанию

Результаты поиска

Содержание AKR 550

Отзывы:

Похожие инструкции для AKR 550

Бренды по названию

Популярные бренды