ESD QUICK 713 Скачать руководство пользователя

Страница: 19 / 26

Diameter of hole is widened through erosion.

Solder plating

Properly maintained, the de-soldering gun should provide years of good service. Efficient de-soldering depends on

the temperature, and the quality and quantity of the solder and flux. Perform the following service procedures as

indicated by the conditions of the gun’s usage.

WARNING:

Since the de-soldering gun can reach a very high temperature, please work carefully. Except when cleaning

the nozzle and heating element, always turn the power switch off and disconnect the power plug before

performing any maintenance procedure.

9.2.1 Daily maintenance

Clean the solder and flux in the suction and the heater element.

After cleaning the suction nozzle with the sponge, coat a new solder at its plate to protect the solder plate.

The filter is expendable, and it often should be replaced to ensure the suction is normal. Pull out the hose each

side filter take out it, replace a new one (refer to the

connection

9.2.2 Servicing the de-soldering gun

CAUTION:

The de-soldering gun will be extremely hot. During the maintenance, please wear gloves and
work carefully.

1. Inspect and clean the nozzle.

(1) Plug in the power cord, turn the power switch on and let the nozzle heat up.

(1)

Clean out the hole of the nozzle heat up.

(2)

Check the condition of the solder plating on the tip of the nozzle. If it is slightly worn, recoat the tip

with fresh solder to prevent oxidation.

(3)

Check the condition of the surface and inside hole of the nozzle. If either is worn or eroded, or the inside

diameter seems unusually wide, replace the nozzle.

Note: The cleaning pin will not pass through the nozzle until the solder inside the nozzle is completely

melted. Please use the proper sized cleaning pin for the nozzle diameter.

CAUTION:

Unfortunately, it is often difficult to observe this condition. Therefore, if desoldering efficiency goes

down and all other parts run in well, the nozzle is probably eroded and should be replaced.

The inside hole and the surface of the nozzle is plated with a special alloy. Should this alloy become

eroded by high-temperature solder, the nozzle will not be able to maintain the proper temperature.

2. Disassemble the heating element

Remove the nut with the heat resistant pad.

The cleaning pin passes completely through the hole.

Содержание QUICK 713



























Результаты поиска

Содержание QUICK 713

Отзывы:

Похожие инструкции для QUICK 713

Бренды по названию

Популярные бренды

ESD QUICK 713, Инструкция по эксплуатации

Результаты поиска

Содержание QUICK 713

Отзывы:

Похожие инструкции для QUICK 713

Бренды по названию

Популярные бренды