background image

1. Read this manual carefully before starting assembly.

Read each step completely before beginning

each step.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons

before assembling or ordering parts.

3. Tomake assembly of your basketball system easier,  use the Hardware Identifier on page 3

and 4 to identify and sort all fasteners. Check all cartons for kits. All hardware is not
located in one kit.

4. Do not tighten hardware until instructed to do so.

If hardware is tightened too soon, mounting

holes may not align and parts may not easily fit together. Leave locknuts slightly loose until you are
instructed to tighten them.

O W N E R ' S M A N U A L

MODEL NO.

B5000

GS72c

BASKETBALL SYSTEM

Please Do Not Return This Product To The Store!

®

Contact Escalade Sports customer service department at:
Phone:

1-888-USA-GOAL

Toll

Free !

Fax:

1-866-873-3536

Toll

Free !

E-mail:

[email protected]

Mailing Address:
Escalade Sports
PO Box 889
Evansville, IN 47706

Please visit our World Wide Web site at:

www.G

 

oalrilla.com

ON-LINE TROUBLE SHOOTING

TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS

FREQUENTLY ASKED QUESTIONS

ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2017 Escalade Sports

5.

An electric screwdriver is helpful in assembly.  However, please

 set at low torque and use caution

 

because you could overtighten the hardware and strip the screws.

Save these instructions and your proof of purchase (receipt) in the event that the manufacturer

6.

has to be contacted for replacement parts.

2L-7580-02

Содержание GOALRILLA B5000


















Отзывы: