ESCALADE GOALRILLA B5000 Скачать руководство пользователя страница 7

Страница: 7 / 17

NOTE: It is important for the installer to understand the
necessity of the Plastic washers (#5) provided. These
washers adequately space painted parts at all pivot points.
Neglecting the use of these washers will result in rusted
parts.

NOTE: All board arms are made of rectangular tubing.
Tightening hardware too tight may damage tubing and
make adjustment of system difficult.

Attach lower arm (#11) to Pole (#2), as shown in Figure 5,
using a bolt (#8), two flatwashers (#3), four plastic washers
(#5) and thin locknut (#49).

Note: make sure "Goalrilla lettering is right side up. Do
NOT tighten bolt (#8) at this time.

Figure 5

Figure 6

Secure Actuator (#16) to Lower Arm (#11) using one bolt
(#8), two flatwashers (#3), four plastic washers (#5) and one

snug but, do not over tighten. Board Arms must pivot

freely.

thin locknut (#49). See Figure 6. Tighten both bolts (#8)

Содержание GOALRILLA B5000


















Результаты поиска

Содержание GOALRILLA B5000

Отзывы:

Похожие инструкции для GOALRILLA B5000

Бренды по названию

Популярные бренды

ESCALADE GOALRILLA B5000, Руководство пользователя

Результаты поиска

Содержание GOALRILLA B5000

Отзывы:

Похожие инструкции для GOALRILLA B5000

Бренды по названию

Популярные бренды