background image

Network Ernitec Cloud Bullet Camera

·

Quick Start Guide

 

 

 

Proper configuration of all passwords and other security settings 
is the responsibility of the installer and/or end-user. 

Cautions

 

 

Make sure the power supply voltage is correct before using the 
camera. 

 

Do not drop the camera or subject it to physical shock. 

 

Do not touch sensor modules with fingers. If cleaning is 
necessary, use clean cloth with a bit of ethanol and wipe it 
gently. If the camera will not be used for an extended period, 
please replace the lens cap to protect the sensor from dirt.   

 

Do not aim the camera at the sun or extra bright places. 
Blooming or smearing may occur otherwise (which is not a 
malfunction), and affect the endurance of sensor at the same 
time. 

 

The sensor may be burned out by a laser beam, so when any 
laser equipment is in using, make sure that the surface of sensor 
will not be exposed to the laser beam. 

 

Do not place the camera in extremely hot, cold (the operating 
temperature shall be-30°C ~+60°C, or -40°C ~ +60°C if the 
camera model has an “H” in its suffix), dusty or damp locations, 
and do not expose it to high electromagnetic radiation.   

 

To avoid heat accumulation, good ventilation is required for 
operating environment.   

 

Keep the camera away from liquid while in use. 

Содержание MicroView MVCLOUD-201
































Отзывы: