LBI-39055
21
must be initialized as described in the following section
before dispatch operations can be performed.
DATABASE INITIALIZATION
When the console initializes from a cold start, all of
the following sections should be performed to insure proper
operation. All console databases are initialized via
commands from the CEC/IMC Manager (MOM PC). See
the CEC/IMC Manager operations guide LBI-38911
(version 2.x) or LBI-39024 (version 3.x) for additional
details.
Basically, except for sending console configurations,
all procedures presented in this section assume all
CEC/IMC console configurations are complete as described
in the CEC/IMC Digital Audio Switch Installation, Set-Up
And Troubleshooting maintenance manual, LBI-38938. See
"STEP 6 - CONSOLE CONFIGURATION" in LBI-
38938 for details.
Console User Profile Configuration
From the CEC/IMC Manager, user profile data is sent
only to the targeted console. When a target console receives
user profile data from the CEC/IMC Manager it will send
an acknowledgment to the CEC/IMC Manager. Send user
profile data to the console as follows:
1. From the CEC/IMC Manager's "
CEC/IMC MOM
Options
" main menu, select the "
Console
Configuration
" option. This will display the
console configuration sub-menu.
2. From this sub-menu, select the "
Console User
Profile
" option. This will display the
"
CONSOLE USER PROFILE
CONFIGURATION
" screen.
3. Verify
the "
CONSOLE
" number matches the CIM's
console number as defined by the CIM's DIP
switches.
4. Verify
the "
Unit ID
" number does not conflict
with that of any other console or radio ID number
in the system.
5. Select
the correct "
Setup
" and then make any
required modification(s) to the configuration. If
required, save the new configuration.
6. Press the <F7> function key to send the Console
User Profile configuration to the console.
7. When the "
User Profile Successfully
Written...
" message is displayed, return to the
CEC/IMC Manager' main menu. If an "
Unable
to Write User Profile...
" message
appears or no message appears after ten (10)
seconds, the CIM
may not be properly installed
and/or configured. Check Controller Board
installation and DIP switch settings. A "
User
Profile Successfully Written...
"
message must be received before continuing with
the next procedure.
System Manager Database Uploads
System Manager databases contain all system
information for all defined entities (units, groups, sites).
These databases can be downloaded by the console by
requesting database uploads from the CEC/IMC Manager.
Since this data is broadcast to all consoles in the CEC/IMC
system, if possible, all consoles should be on-line when this
upload occurs. This avoids having to repeat the process for
other consoles at a later time.
1. From the CEC/IMC Manager's "
CEC/IMC MOM
Options
" main menu, select the "
System
Manager Data
" option. This will display a sub-
menu.
2. Select
"
Upload From System Manager
".
3. From the "
SYSTEM MANAGER UPLOAD
STATUS
" screen, select <F1> then <F8> for a full
unit upload. After the upload is complete, exit the
screen by pressing <Esc>.
4. From the "
SYSTEM MANAGER UPLOAD
STATUS
" screen, select <F2> then <F8> for a full
group upload. After the upload is complete, exit
the screen by pressing <Esc>.
5. From the "
SYSTEM MANAGER UPLOAD
STATUS
" screen, select <F6> then <F8> for a full
site upload. After the upload is complete, exit the
screen by pressing <Esc>.
6. From the "
System Manager Data
" sub-menu,
select the "
Upload From MOM PC
" option.
7. From the "
MOM PC BASED SYSTEM MANAGER
UPLOAD STATUS
" screen, select <F3> then
<F8> for a full conventional channel upload. After
the upload is complete, exit the screen by pressing
<Esc>.
8. From the "
MOM PC BASED SYSTEM MANAGER
UPLOAD STATUS
" screen, select <F5> then
<F8> for a full console upload. After the upload is
complete, exit the screen by pressing <Esc>.
