Ericsson 1553-FGC 101 1010 Uen A Скачать руководство пользователя страница 43

Страница: 43 / 153

SD-SDI Input and LOCK Indicator at the Rear Panel

LED State Description

Audio Input

Digital Support

Digital audio may be input via the 15-way D-type connector labelled AUDIO/DATA.

15-way D-type at the Rear Panel

See

Technical Specification

for further details.

Breakout Cables

The digital audio can either be balanced (AES3) or unbalanced (AES3-id) depending upon the audio breakout cable used:

NOTE :

An audio breakout cable is NOT supplied as standard with the chassis, but must be ordered separately.

The chassis detects which cable is fitted (balanced or unbalanced) and selects appropriately.

The picture alongside shows the Video input connector: SD-SDI 75 Ω
female BNC socket at the module rear panel.
Also illustrated is the LED indication for SD SDI lock status.

The LED (marked

LOCK

at the module rear panel) is used to show the

status of the module and/or incoming video signal.

LED State

Description

Off

The SDI Input is not active.

Red

The SDI Input is active, but not locked.

Green

The SDI Input is active and is locked.

Alternate Red and Green

The SDI Input is active, but video of the wrong line standard is being
received.

The 15-way D-type supports digital audio balanced and
unbalanced signals (but not at the same time).

Marketing Code

Part Number

Supported Audio Mode

VP/CAB/BAL

S14936 Audio Breakout Cable

Balanced Audio: 4 XLRs in + 1 BNC for ref tone
out

VP/CAB/UNBAL

S14937 Audio Breakout Cable

Unbalanced Audio: 4 BNCs in + 1 BNC out for

ref

tone out

AES3

AES-3id

Interface

Balanced

Unbalanced

Connector

XLR-3

BNC

Impedance

110 Ω

75 Ω

Input Level

2-7 V peak to peak 1 V peak to peak

Page 43 of 153

Cover

9/11/2012

file://C:\Users\ebriacl\AppData\Local\Temp\~hh7DF.htm

Содержание 1553-FGC 101 1010 Uen A

























































































































































Результаты поиска

Содержание 1553-FGC 101 1010 Uen A

Отзывы:

Бренды по названию

Популярные бренды

Ericsson 1553-FGC 101 1010 Uen A, Руководство пользователя

Результаты поиска

Содержание 1553-FGC 101 1010 Uen A

Отзывы:

Бренды по названию

Популярные бренды