Erco & Gener GenPro 22e Скачать руководство пользователя

Страница: 51 / 63

EG_GenPro2xe_1003_UG_005_UK

Page 51 / 63

Descriptions and non-contractual illustrations in this document are given as an indication only.

ERCO&GENER reserves the right to make any modifications.

Dct_427_00

Table 4 : Consumption with internal battery Without external power supply

CONDITIONS

850 MHz

900 MHz

1800 MHz

1900 MHz

T=25°C et carte SIM 3V

I Nom.(mA) I Nom.(mA) I Nom.(mA) I Nom.(mA)

Idle mode (2*)

@ 3.8V

In GSM communication

3.8V

283 281 248 237

1RX/1TX, Full Power
Power (2W/1W)
In GPRS CL10 communication

3.8V

453 455 387 373

2RX/2TX, Full Power
Power (2W/1W)
During TX bursts

3.8V

1633 1633 1313 1213

Power (2W/1W)

(1*) The power supply consumption may vary by 5% depending on the temperature range (-20 °C to +55 °C).
(2*) Idle mode = modem registered on network but not in communication.

8.2.2 Audio interface

The audio interface is available via the 15-pin Sub HD connector, see the paragraph 7.9 Audio.

8.2.2.1 Microphone

Characteristics recommended for the microphone

Mic Input

Parameter/Conditions

Min

Typ

Max

Units

Maximum Input Range –
Mic(+) to Mic(-)

Inputs 3 dBm0 (Max. digital
sample amplitude when PGA
gain set to 0 dB)

32.5

RMS

Nominal Ref. Level –
Mic(+) to Mic(-)

Differential MIC

-10

dBm0

Differential Input Resistance –
Mic(+) to Mic(-)

Differential MIC,

MICAMP

gain = 25.6 dB

36 k

Ω

Microphone Pre-Amplifier Gain

Differential MIC

25.6

Содержание GenPro 22e
































































Результаты поиска

Содержание GenPro 22e

Отзывы:

Похожие инструкции для GenPro 22e

Бренды по названию

Популярные бренды

Erco & Gener GenPro 22e, Руководство пользователя

Результаты поиска

Содержание GenPro 22e

Отзывы:

Похожие инструкции для GenPro 22e

Бренды по названию

Популярные бренды