Epygi QuadroM-E1 Скачать руководство пользователя страница 7

Страница: 7 / 55

QuadroM-E1/T1 Manual I: Installation Guide

Hardware Overview

QuadroM-E1/T1; (SW Version 5.2.x)

Hardware Overview

QuadroM-E1/T1’s Rear Panel

Fig. I-1: Single E1T1 QuadroM-E1/T1's front panel

Fig. I-2: Dual E1/T1 QuadroM-E1/T1's front panel

Fig. I-3: QuadroM-E1/T1's backpanel

PHONE socket with a RJ-11 connector enables connectivity of a regular analog tele-

phone. This is a FXS (Foreign Exchange Station) analog port.

The Reset button may be used in two ways: (1) to initiate a normal reset, (2) to carry

out a factory reset. A normal reset is executed by pressing the Reset button with a pa-
per clip for an instant.

Pressing the reset button and holding it down for 7 seconds or more will execute a fac-
tory reset. This will restore the factory defaults and clear all settings including the IP
address and the administration password you entered.

Please Note

: A Factory Reset forces the default LAN IP address of 172.30.0.1 and

default administrator's password of 19.

RJ-45 socket to attach the E1/T1 trunk. Depending on the model of QuadroM-E1/T1,

there might be one or two E1/T1 trunks. See

Appendix: Pin Assignment of E1/T1.

RJ-45 sockets to attach two Local Area Networks (LANs) via Ethernet CAT 5 cables. If

a PC is connected directly to this socket, a straight cable is used. If an Ethernet hub,
router or switch is used, a crossover cable may be required.

RJ-45 socket to attach the Internet Uplink (WAN) via an Ethernet CAT 5 cable.

Power supply socket. Use only the power adapter delivered with the QuadroM-

E1/T1.

Power switch to turn on/off the device.

Содержание QuadroM-E1
























































Результаты поиска

Содержание QuadroM-E1

Отзывы:

Бренды по названию

Популярные бренды

Epygi QuadroM-E1, Руководство по установке

Результаты поиска

Содержание QuadroM-E1

Отзывы:

Бренды по названию

Популярные бренды