Epson Stylus Pro 9000 Скачать руководство пользователя страница 70

Страница: 70 / 165

3-15

Maintaining and Transporting the Printer

3-15

Cleaning the Printer

To keep your printer working at its best, you should clean it thoroughly
several times a year.

1. Make sure the printer is turned off and all the lights on the control panel

are off. Then unplug the power cord.

2. Open the roll paper cover and remove the roll paper spindles. Remove

any sheet media from the printer.

3. Make sure the ink cartridge compartments are closed. Then use a soft

brush to carefully clean away any dust or dirt.

4. Close the roll paper cover.

5. Open the lower cover and use a soft brush to carefully clean away any

dust or dirt inside the lower cover. Then close the cover.

6. Remove the paper hammock. Then clean away any dust or dirt around

the leg assembly using a soft brush.

7. If the outer case is dirty, clean it with a soft, clean cloth dampened with

mild detergent. Keep the ink cartridge compartment closed to prevent
water from getting inside.

8. If the area under the roll paper cover accidentally gets soiled with ink,

wipe it off with a damp cloth.

9. To wash the paper hammock, remove the shafts, then machine wash

with mild detergent and air dry.

Caution

Be careful not to touch
the gears inside the
printer.

To avoid damaging the
components as well as
the case, never use
alcohol or thinners to
clean the printer.

Be careful not to get
water on the printer
mechanism or electronic
components.

Don’t use a hard or
abrasive brush.

Don’t spray the inside
of the printer with
lubricants; unsuitable
oils can damage the
mechanism. Contact your
dealer or a qualified
servicer if your printer
needs lubrication.

Содержание Stylus Pro 9000






































































































































































Результаты поиска

Содержание Stylus Pro 9000

Отзывы:

Похожие инструкции для Stylus Pro 9000

Бренды по названию

Популярные бренды

Epson Stylus Pro 9000, Руководство принтера

Результаты поиска

Содержание Stylus Pro 9000

Отзывы:

Похожие инструкции для Stylus Pro 9000

Бренды по названию

Популярные бренды