Epson Stylus Pro 9000 Скачать руководство пользователя страница 33

Страница: 33 / 165

1-16

1-16

Handling Paper and Other Media

Before you start, make sure the printer is on and roll paper is not loaded for
printing. Then follow these steps:

1. Make sure the roll paper cover is closed.

2. Press the

Paper Source

button repeatedly until the

Sheet

light

comes on.

3. Make sure that the paper set lever is all the way down.

4. Feed the sheet into the paper slot until it meets resistance. Make sure the

right edge of the paper is straight and aligned with the scale on the roll
paper cover.

PRESS PAUSE BUTTON

appears on the control panel

display.

5. Press the

Pause

button. The print head moves and the sheet feeds into

printing position automatically.

READY

appears on the LCD panel.

(Even if you don’t press

Pause

, the paper and printer will move into

printing position automatically after 10 seconds.)

6. Print your page. After it is finished, the sheet stays in the printer.

7. To remove your print, hold it while pressing the

Paper Feed (–)

button.

Содержание Stylus Pro 9000






































































































































































Результаты поиска

Содержание Stylus Pro 9000

Отзывы:

Похожие инструкции для Stylus Pro 9000

Бренды по названию

Популярные бренды

Epson Stylus Pro 9000, Руководство принтера

Результаты поиска

Содержание Stylus Pro 9000

Отзывы:

Похожие инструкции для Stylus Pro 9000

Бренды по названию

Популярные бренды