Epson S5U1C63000A, Руководство пользователя

Страница: 252 / 346

CHAPTER 8: DEBUGGER
238
EPSON
S5U1C63000A MANUAL
(S1C63 FAMILY ASSEMBLER PACKAGE)
8.10 Status/Error/Warning Messages
1. ICE status messages
Status message Content of message
Break by PC break Break caused by PC breakpoint
Break by data break Break caused by data break condition
Break by register break Break caused by register break condition
Break by sequential break Break caused by sequential break condition
Key Break Break caused by pressing [ESC] key or [Key break] button
Break by accessing no map program area Break caused by accessing undefined program-memory area
Break by accessing no map data area Break caused by accessing undefined data-memory area
Break by accessing ROM area Break caused by writing to data ROM area
Out of SP1 area Break caused by accessing outside SP1 stack area
Out of SP2 area Break caused by accessing outside SP2 stack area
Break by external break Break caused by signal input to ICE BRKIN pin
2. ICE error messages
Error message Content of message
communication error Communication error other than time-out
(overrun, framing, or BCC error)
CPU is running Target is running.
ICE is busy ICE is busy processing a job.
ICE is free run mode ICE is operating in free-run mode.
ICE is maintenance mode ICE is placed in maintenance mode.
no map area, XXXX No-map area is specified for accessing.
not defined ID, XXXX ICE respond ID is invalid.
on tracing System is tracing execution data.
reset time out CPU cannot be reset (for more than 1 second).
target down Peripheral Circuit Board does not operate correctly or remains reset.
Time Out! Communication time-out
3. Flash memory error messages
Error message Content of message
flash memory error, XXXX Writing or erasing flash memory has failed at XXXX.
flash ROM is protected Flash memory is protected against access.
format error Flash memory is not mapped.
Map information is not the same Map information loaded from parameter file does not match that in
the parameter file.
verify error, XXXX Verify error has occurred when data was written to flash memory.
4. Command error/warning messages
Error message Content of message (Commands involved)
Address out of range, use 0–0xXXXX The specified program memory address is out of range.
(a/as, pe, pf, pm, sc, m, u, g, gr, bp, bc, bs, tm, ts, cv)
Address out of range, use 0–0xFFFF The specified data memory address is out of range.
(dd, de, df, dm, dw, bd, ts)
Cannot load program/ROM data, check ABS file Failed to load program/ROM data; some file other than IEEE-695
executable format was specified. (lf)
Cannot open file The file cannot be opened.
(lf, lo, com, cmw, log, rec, xfwr/xfwrs, xfcp/xfcps)
Data out of range, use 0–0xF The specified number is out of the data range. (de, df)
Different chip type, cannot load this file A different ICE parameter is used in the file. (lf)
end address < start address The start address is larger than the end address.
(pf, pm, df, dm, bd, cv, xdp/xdps)
error file type (extension should be CMD) The specified file extension is invalid. (com, cmw)
FO address out of range, use 0–0xEF FO address is invalid. (od)
illegal code The input code is not available. (pe, pf)
illegal mnemonic The input mnemonic is invalid for S1C63000. (a/as)
Incorrect number of parameters The parameter number is incorrect. (All commands)
Incorrect option, use -f/-u/-i/-s/-c/-il/-cm An invalid mode setting option was specified. (md)
Incorrect r/w option, use r/w/* An illegal R/W option was specified. (bd)
Incorrect register name, use A/B/X/Y/F An invalid register name was specified. (br)