Epson RP-U420 Series Скачать руководство пользователя страница 76

Страница: 76 / 84

Confidential

EPSON

TITLE

SHEET
REVISION

NO.

SHEET

RP-U420 series

Specification

(STANDARD)

= 4: Paper roll sensor status

Bit

Off/On

Hex

Decimal

Function

Off

Not used. Fixed to Off.

Not used. Fixed to On.

Off

Journal paper roll is not near-end.

Journal paper roll near-end is detected.

Off

Receipt paper roll is not near-end.

Receipt paper roll near-end is detected.

Not used. Fixed to On.

Off

Journal mark sensor does not detect black mark.

Journal mark sensor is detecting black mark.

Off

Receipt mark sensor does not detect black mark.

Receipt mark sensor is detecting black mark.

Off

Not used. Fixed to Off.

= 6: Validation status

Bit

Off/On

Hex

Decimal

Function

Off

Not used. Fixed to Off.

Not used. Fixed to On.

Off

Validation is not selected.

Validation is selected.

Off

Not validation insertion waiting state.

Within validation insertion waiting state.

Not used. Fixed to On.

Off

Validation sensor does not detect paper.

Validation sensor is detecting paper.

Off

Reserved. Fixed to Off.

Off

Not used. Fixed to Off.

[Notes]

•

The status is transmitted whenever the data sequence of <10>H <04>H <

≤

4 or 6) is received.

Example:
In ESC

∗

m n

d1...dk

=<10>H,

=<04>H,

=<01>H

Содержание RP-U420 Series





















































































Результаты поиска

Содержание RP-U420 Series

Отзывы:

Похожие инструкции для RP-U420 Series

Бренды по названию

Популярные бренды

Epson RP-U420 Series, Спецификация

Результаты поиска

Содержание RP-U420 Series

Отзывы:

Похожие инструкции для RP-U420 Series

Бренды по названию

Популярные бренды