Epson RP-U420 Series Скачать руководство пользователя страница 58

Страница: 58 / 84

Confidential

EPSON

TITLE

SHEET
REVISION

NO.

SHEET

RP-U420 series

Specification

(STANDARD)

•

The defined downloaded characters are cleared in the following circumstances:

1) When deleted by ESC ?.
2) When ESC @ is executed.
3) When the printer is reset or turned off.

4) When a hardware reset is executed or the power is turned off.

•

No user-defined characters are defined in the initial state.

•

If any user-defined characters are not defined, the internal character set (built-in) is
selected.

[Example]

9 font with 2-dot character space

LSB

MSB

LSB

MSB

When the dot pattern for code 20H is defined as shown above.

ESC &

p10 p11 p12 p13 p14

Code 1B

80 00

The corresponding bit is 1 when printing and 0 when not printing.

[Note]

•

If the ESC R

is executed, the user-defined characters which have been already

defined are canceled.

Содержание RP-U420 Series





















































































Результаты поиска

Содержание RP-U420 Series

Отзывы:

Epson RP-U420 Series, Спецификация, Страница: 58 / 84

Результаты поиска

Содержание RP-U420 Series

Отзывы: