Epson RP-U420 Series Скачать руководство пользователя страница 46

Страница: 46 / 84

Confidential

EPSON

TITLE

SHEET
REVISION

NO.

SHEET

RP-U420 series

Specification

(STANDARD)

3.4 Panel LED Indicators

3.4.1 Panel LED indicators

1) Power supply (POWER) LED: Green

ON:

Power supply is stable.

OFF:

Power supply is not stable.

2) Receipt/Journal paper roll near-end (PAPER OUT) LED: Red

ON:

Near-end or end of paper roll is detected. (*1)

OFF:

Adequate paper remains on the paper roll (normal condition).

Blinking: See Table 3.4.1 for the meanings. (Both a receipt and a journal LED blink)

*1: A near-end detector is installed.

Table 3.4.1 Printer Status In Blinking

Printer Status

Receipt/Journal LEDs blinking pattern

A self-test printing is in a wait state.

320ms

approx.320ms

The printer waits for a validation
paper to be inserted.

160ms

approx.160ms

The printer waits for a validation
paper to be removed.

approx.160ms

160ms

2.56sec

3) Error (ERROR) LED: Red

ON:

Offline (except during paper feeding using the paper feed button and during the self-
test).

Blinking:

Error state. (See Section 3.5, Error Processing)

OFF:

Normal operation.

Содержание RP-U420 Series





















































































Результаты поиска

Содержание RP-U420 Series

Отзывы:

Похожие инструкции для RP-U420 Series

Бренды по названию

Популярные бренды

Epson RP-U420 Series, Спецификация

Результаты поиска

Содержание RP-U420 Series

Отзывы:

Похожие инструкции для RP-U420 Series

Бренды по названию

Популярные бренды