Epson RP-U420 Series Скачать руководство пользователя страница 45

Страница: 45 / 84

Confidential

EPSON

TITLE

SHEET
REVISION

NO.

SHEET

RP-U420 series

Specification

(STANDARD)

2) Parallel interface model

Table 3.3.3 DIP Switch 1

Switch

No.

Function

OFF

Reserved

Fixed to Off.

Reserved

Fixed to Off.

Reserved

Fixed to Off.

Reserved

Fixed to Off.

Reserved

Fixed to Off.

Busy condition

Refer to Table 2.1.1

Paper cutter

Manual cutter

Auto cutter

Printer mode selection

Taiwan mode *1)

Standard mode *2) *3)

Table 3.3.4 DIP Switch 2

Switch

No.

Function

OFF

Pin 31 reset signal

Used

Not used

Reserved

Fixed to Off.

Buzzer

Enabled

Disabled

Reserved

Fixed to Off.

Download mode

Enabled

Disabled

Reserved

Fixed to Off.

*1) Taiwan mode:

Printer mode which is used for Taiwan market
This mode can be set to the printer which is equipped with the
Taiwan black mark sensor.

Receipt paper feed button: Feeds paper with one short pressing the button

Continuous pressing the button which exceeds for 2 seconds feeds
paper to the next mark sensor setting position then cuts the paper
with one point left uncut.

Journal paper feed button:

Feeds paper with one short pressing the button

Continuous pressing the button which exceeds for 2 seconds feeds
paper to the next mark sensor setting position.

FF command:

Prints the data in the print buffer and feeds to the next print starting
position on the receipt and cut (one point left uncut).

GS V command:

Feed paper to the preprint black mark position then cuts the paper.

*2) Standard mode:

Printer mode which is used except for Taiwan market

FF command:

Ignored in this mode.

*3) Printing for paper without the preprint black mark must be set to the DIP SW1-8 to Off (standard

mode).

Содержание RP-U420 Series





















































































Результаты поиска

Содержание RP-U420 Series

Отзывы:

Похожие инструкции для RP-U420 Series

Бренды по названию

Популярные бренды

Epson RP-U420 Series, Спецификация

Результаты поиска

Содержание RP-U420 Series

Отзывы:

Похожие инструкции для RP-U420 Series

Бренды по названию

Популярные бренды