Epson RP-U420 Series Скачать руководство пользователя страница 57

Страница: 57 / 84

Confidential

EPSON

TITLE

SHEET
REVISION

NO.

SHEET

RP-U420 series

Specification

(STANDARD)

ESC % n

[Name]

Select/cancel user-defined character set

[Format]

ASCII

ESC

Hex

Decimal

[Range]

≤

255

[Default]

= 0

[Function]

Selects or cancels the user-defined character set.

When the Least Significant Bit (LSB) is 0, the user-defined character set is canceled and
the internal character set is enabled.

When the LSB is 1, the user-defined character set is selected.

[Description]

•

Only the least significant bit of n is valid.

•

When the user-defined character set has been released, the internal character set is
specified automatically.

ESC & y c1 c2 [x1 d1...d(y

××××

x1)]...[xk d1...d(y

××××

xk)]

[Name]

Define user-defined characters

[Format]

ASCII

ESC

c2 [x1 d1...d(y

x1)]...[xk d1...d(y

xk)]

Hex

c2 [x1 d1...d(y

x1)]...[xk d1...d(y

xk)]

Decimal

c2 [x1 d1...d(y

x1)]...[xk d1...d(y

xk)]

[Range]

≤

126

≤

255

+ 1

[Function]

Defines user-defined characters.

•

specifies the number of bytes in the vertical direction.

•

specifies the beginning character code for the definition, and c2 specifies the final

code.

•

specifies the number of dots in the horizontal direction.

•

specifies the defined character data pattern.

[Description]

•

Consecutive character codes for multiple characters can be defined in one definition.

•

" is definition data that indicates the pattern for "

" dots in the horizontal direction,

starting from the left edge. If "

" does not satisfy dots in the character configuration

pattern (9 dots), the remaining dots on the right are spaces.

•

In the definition data, a "1" represents a dot that is to be printed, and a "0" represents a
dot that is not to be printed.

•

Only the most significant bit of the second data byte in the vertical direction can be
printed.

•

Independent user-defined character definitions are possible for the fonts if the
character pattern is different in the international character sets.

Содержание RP-U420 Series





















































































Результаты поиска

Содержание RP-U420 Series

Отзывы:

Похожие инструкции для RP-U420 Series

Бренды по названию

Популярные бренды

Epson RP-U420 Series, Спецификация

Результаты поиска

Содержание RP-U420 Series

Отзывы:

Похожие инструкции для RP-U420 Series

Бренды по названию

Популярные бренды