Epson Perfection 3200 Photo Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 78

background image

EPSON Perfection 3200 Photo

Revision A

Operating Principles

Power Supply Circuit

19

2.2 Power Supply Circuit

Power supply circuit in this scanner generates direct current DC power
necessary for driving the controller board and scanner engine. Table below
shows each power supply circuit for different destinations.

Table 2-1. Power Supply Circuit Board for Destination

Figure 2-5 shows diagram of power supply circuit.
Output from the power supply circuit is performed by closing or opening the No.
4 pin of CN102 connector. When opening, as it is shown in the Table below,
each output voltage becomes active. Also, each output voltage has over
current protection and over voltage protection circuit.

Table 2-2. Output and Protection Function

NOTE:

1. If a part of output is shut down, all the other output are also shut
down.
2. Off time required to recover is maximum 5 minutes.

Specification

Unit Part No.

Fuse

100-120 VAC Range

2027705

2.5 A/125 VAC

220-240 VAC Range

2027704

T2.5AH/250 VAC

Output

Voltage

Output

Current

Over Current Protection

(Current value to activate)

Over voltage Protection

(Voltage value to activate)

5 VDC

1.2A

Fold-back characteristic.

Automatic Recovery.

(Less than 1A)

Shut down. Turn off the

power and back on to

recover. (5.5 -7.5 VDC)

12 VDC

0.2A

Constant current limiting.

Automatic Recovery.

(less than 0.5 A)

Shut down. Turn off the

power and back on to

recover. (14 -17 VDC)

24 VDC

0.7A

Shut down. Turn off the

power and back on to

recover.

Shut down. Turn off the

power and back on to

recover. (28 -33 VDC)

«
...
22
23
24
25
26
...
»

Содержание Perfection 3200 Photo















































































Отзывы:

Нет отзывов

Похожие инструкции для Perfection 3200 Photo

Бренд: Hand Held Products Страницы: 180

FLATSCAN REV PZ

Бренд: LZR Страницы: 12

Black Bluetooth Scanner

Бренд: Seaward Страницы: 3

Бренд: Uniden Страницы: 84

ONETOUCH 7400 USB

Бренд: Visioneer Страницы: 2

OneTouch 5300 Series

Бренд: Visioneer Страницы: 40

Бренд: IRISPen Страницы: 14

Бренд: IRIS Страницы: 30

IRISPen Translator 6

Бренд: IRIS Страницы: 66

Бренд: C-Pen Страницы: 13

Бренд: Iron logic Страницы: 6

Бренд: TEC Страницы: 16

MobileOffice H100

Бренд: Plustek Страницы: 2

Бренд: Plustek Страницы: 47

Бренд: Hasselblad Страницы: 22

Бренд: Faro Страницы: 36

Бренд: Radio Shack Страницы: 52

Бренд: Magnasonic Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды