Epson GT-1200 Скачать руководство пользователя страница 29

Страница: 29 / 157

GT-12000

Troubleshooting

Rev. A

3-4

Flowchart 3-2
Phenomenon: CR (Mirror/Lamp) does not move.

Start

With the scanner power On, check the
connector CN5 on the B054MAIN
board for the c24 VDC output
from the following :

Between Pin 1 and Pin 4 : +24 VDC

Turn th scanner off and move the CR

manually to check if it moves smoothly.

Does the CR move abnomrmally?

The mechanism is
abnormal.
(Needs replacing.)

Unlock the screw.

Yes

Is the transportation

screw set to the locking

position?

Is the correct voltage output?

Replace the

B054PSH board.

Yes

Check the following motors for
the correct resistance:
- Motor (for mirror) : 15.0

- Motor (for focus) : 15.5

Are the resistances correct?

Check the motor driver ICs on
the B054MAIN board.

<Motor (for mirror) >
Check if the resistance
between Pin 8/6 of IC4/3 and
the GND is infinitive.

<Motor(focus)>
Check if the resistance
between Pin 1/15 of IC5/6 and
the GND is infinitive.

Replace the

B054MAIN

board.

Are they correct?

Replace the

motor.

Yes

Replace the

B054MAIN

board.

Содержание GT-1200






























































































































































Результаты поиска

Содержание GT-1200

Отзывы:

Похожие инструкции для GT-1200

Бренды по названию

Популярные бренды

Epson GT-1200, Руководство по обслуживанию

Результаты поиска

Содержание GT-1200

Отзывы:

Похожие инструкции для GT-1200

Бренды по названию

Популярные бренды