Epson GT-1200 Скачать руководство пользователя страница 126

Страница: 126 / 157

ADF

Adjustment

Rev. A

5-1

5.1 OVERVIEW

This chapter describes adjustments required after disassembling and
assembling the ADF or replacing specified parts. Adjustment items of this
ADF fall in 2 categories: mechanical adjustment and electrical adjustment.

5.1.1 Adjustment Tools

The tools used for the mechanical and electrical adjustment are described
below:

Table 5-1. Tool List

Tool Names

Availability

SE Part No.

Thickness Gauge

Available

B776702201

Tension Gauge

Available

B765114601

The electrical adjustments are made on the built-in program. Therefore,
no tool is required.

5.1.2 Mechanical Adjustment

This section describes the mechanical adjustment for the ADF. The table
below lists the adjustment items and the corresponding occasions.

Table 5-2. Mechanical Adjustment Items

Adjustment items

Occasions

Flapper solenoid installation
position adjustment
(Refer to Section 5.1.2.1.)

Flapper solenoid is removed.

Flapper solenoid is replaced.

Separation plate gap adjustment
(Refer to Section 5.1.2.2.)

Separation plate is removed.

Separation plate is replaced.

Belt tension adjustment
(Refer to Section 5.1.2.3.)

Whole belt roller (left) fixing unit is
removed.

The belt is loosened.

Magnet catch installation position
adjustment
(Refer to Section 5.1.2.4.)

Magnet catch is removed.

Magnet catch is replaced.

ADF open/close micro switch
installation position adjustment
(Refer to Section 5.1.2.5.)

Micro switch is removed.

Micro switch is replaced.

Skew correction adjustment
(Refer to Section 5.1.2.6.)

ADF is removed from the rear
case.

Scanned image is skewed.

Fed document jams.

Содержание GT-1200






























































































































































Результаты поиска

Содержание GT-1200

Отзывы:

Похожие инструкции для GT-1200

Бренды по названию

Популярные бренды

Epson GT-1200, Руководство по обслуживанию

Результаты поиска

Содержание GT-1200

Отзывы:

Похожие инструкции для GT-1200

Бренды по названию

Популярные бренды