Epson GT-1200 Скачать руководство пользователя страница 28

Страница: 28 / 157

GT-12000

Troubleshooting

Rev. A

3-3

Flowchart 3-1
Phenomenon: “Operate” LED does not light.

Disconnect the cables from the
connectors CN2/4/5/6/7 on the
B054MAIN board, then, with the
scanner power on, check the
connector CN 5 on the B054MAIN
board for the correct voltages shown
below:

Between Pins 1 and 4 : +24VDC
Between Pins 7 and 4 : + 5 VDC
Between Pins 9 and 10 : +15VDC

Are the

CN1 on the B054SUB

board and the shield

compartment connected

properly?

Yes

Start

Has the

fuse F1/F2 on the

B054PSH board

blown out?

Yes

Are the outputs all corrects?

Replace the B054PSH
board.

Yes

Connect them properly.

Replace the

fuse. Has the fuse

blown again at turning

on the scanner?

Replace the B054PSH
board.

Disconnect the connector
cables from the connectors
CN2/4/5/6/7 on the B054SUB
board.

Yes

Check the following motors for
the correct resistance:
- Motor (for mirror) : 15.0

Ω

- Motor (for focus) : 15.5

Ω

Are the resistances correct?

Check the motor driver ICs on
the B054MAIN board.

<Motor (for mirror) >
Check if the resistance
between Pin 8/6 of IC4/3 and
the GND is infinitive.

<Motor(focus)>
Check if the resistance
between Pin 1/15 of IC5/6 and
the GND is infinitive.

Replace the

B054MAIN

board.

Are they correct?

Replace the

motor.

Yes

Replace the

B054MAIN

board.

Содержание GT-1200






























































































































































Результаты поиска

Содержание GT-1200

Отзывы:

Похожие инструкции для GT-1200

Бренды по названию

Популярные бренды

Epson GT-1200, Руководство по обслуживанию

Результаты поиска

Содержание GT-1200

Отзывы:

Похожие инструкции для GT-1200

Бренды по названию

Популярные бренды