Epson GT-1200 Скачать руководство пользователя страница 108

Страница: 108 / 157

ADF

Troubleshooting

Rev. A

3-2

3.1.1.1 Single Feeding Test Mode

With this test mode, you can detect the defective part by setting the
document (including a blank paper) and performing the single feeding.

CHECK POINT

Abnormal phenomenon does not necessary
determine the test mode to be performed.
Therefore, performing all test modes listed in
Table 3-1 one by one in the listed order is
recommended.

Step 1. Place the ADF on the scanner and set it ready for power-on.
Step 2. Set the Dip-switch on the control as shown below.

O n

O f f

Step 3. Turn the scanner on, and open and then close the either feeding

cover or eject cover. (The test mode is set with this action.)

Step 4. Press the push switch on the control board.

CHECK POINT

If the paper jam error occurs, open and close
either feeding or eject cover to clear the error
status.

3.1.1.2 Reverse Feeding Test Mode

With this test mode, you can detect the defective part by setting the
document (including a blank sheet) and performing the reverse feeding.

Step 1. Place the ADF on the scanner and set it ready for power-on.
Step 2. Set the Dip-switch on the control board as shown below.

O n

O f f

Step 3. Turn the scanner on, and open and then close the either feeding

cover or eject cover. (The test mode is set with this action.)

Step 4. Press the push switch on the control board.

Содержание GT-1200






























































































































































Результаты поиска

Содержание GT-1200

Отзывы:

Похожие инструкции для GT-1200

Бренды по названию

Популярные бренды

Epson GT-1200, Руководство по обслуживанию

Результаты поиска

Содержание GT-1200

Отзывы:

Похожие инструкции для GT-1200

Бренды по названию

Популярные бренды