Epson ET-14000 Скачать руководство пользователя страница 52

Страница: 52 / 82

2016/08/25

Revision: 2

Page:

5.1.27 Transfer Raster image ESC i r c b nL nH mL mH d1......dk

ESC i r c b nL nH mL mH d1......dk

Ver 1.00

[Name]

Transfer Raster image

[Format]

1BH,69H, r, c, b, nL, nH, mL, mH, d1,

d2, ..., dk

[Range of Definition]

r = 00H, 01H, 02H, 04H
c = 00H, 01H
b = 01H, 02H
0000H <= (nH*256 + nL) <= 7FFFH
0001H <= (mH*256 + mL) <= 7FFFH

[Function]

1) Prints dot graphics in raster format.
2) Parameters are used as described below:

r :

color of ink

00H:black

01H:magenta

02H:cyan

04H:yellow

40H:black2

c :

compression method

00H:non-compressed
01H:Run Length Encoding

b :

bit length required for each pixel of image data

01H:1bit/pixel (for Micro, Normal x 1 x 2 dot

For every 1 bit of data:

0 no dot

1 a normal size dot for the current dpi

will be printed at the pixel location for that one bit.

02H:2bits per pixel (for dot sizes requiring 2 bits to designate the size)

For every 2 bits of data:

00 no dot

01 a small dot

10 a medium size dot

11 a large size dot

will be printed at the pixel location for those 2 bits.

Sample bits of data (for 4 pixels of an image), and the results of that data,

are displayed in the upcoming diagram.

nL, nH: Horizontal byte count, according to the following formula:

= INT(horizontal byte count / 256)

= INT(((horizontal dot count) * (bit length of each pixel) + 7) / 8) /256

= MOD(horizontal byte count / 256)

= MOD(((horizontal dot count) * (bit length of each pixel) + 7) / 8) /256

mL, mH: Vertical dot count ( rows of dot graphics ), according to the following formula:

mH = INT(vertical dot count / 256)
mL = MOD(vertical dot count / 256)

k :

Total numbers of data bytes, according to the following formula:

k = (nH*256 + nL) * (mH*256 + mL)

** Sample bits of data for 4 pixels of an image using 2 bits data/pixel:

The size of the dot is designated with a binary number, using 2 bits for every 1 picture element.
No Dot: 00, small dot: 01, medium dot: 10, large dot: 11

1 Byte

Data = 0 0 0 1 1 0 1 1 = 0x1B

No Small Middle Large

[Initial State]

Содержание ET-14000



















































































Результаты поиска

Содержание ET-14000

Отзывы:

Похожие инструкции для ET-14000

Бренды по названию

Популярные бренды

Epson ET-14000, Руководство по программированию

Результаты поиска

Содержание ET-14000

Отзывы:

Похожие инструкции для ET-14000

Бренды по названию

Популярные бренды