Epson ET-14000 Скачать руководство пользователя страница 43

Страница: 43 / 82

2016/08/25

Revision: 2

Page:

5.1.19 Select MicroWeave printing mode ESC (i

ESC (i

Ver 1.00

[Name]

Select MicroWeave printing mode

[Operation]

[Format]

1BH, 28H, 69H, 01H, 00H, n

[Range of Definition]

n=00H, 01H, 30H, 31H

[Function]

1) Selects / deselects the MicroWeave mode.

all parameters : deselects

[Initial State]

Non-MicroWeave mode

[Related Commands]

[Setting] Commands whose settings are affected by this command.

This command changes the non-selected state set by either the ESC (G or ESC @
commands.

[Setting] Commands that change the effects of this command.

The ESC (G command sets the non-selected state.

The ESC @ command sets the non-selected state.

[Operation] Commands whose functionality is affected by this command.

None

[Operation] Commands that change the effects of this command.

None

Содержание ET-14000



















































































Результаты поиска

Содержание ET-14000

Отзывы:

Похожие инструкции для ET-14000

Бренды по названию

Популярные бренды

Epson ET-14000, Руководство по программированию

Результаты поиска

Содержание ET-14000

Отзывы:

Похожие инструкции для ET-14000

Бренды по названию

Популярные бренды